Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Regarding the radio peripheral, I stumbled upon these 2 properties and have no idea what they are for.
What's access address? And what is a channel? Shouldn't there be...
I am runing ble_connectivity example with simple_uart instead of app_uart was not working unable to scan not getting advertisement reports.
Its been working with PCA10001...
Hi,
I have a pretty simple problem but I can't get it right. This is what I want to do:
T=000, PIN_x = 0
T=004, PIN_x = 1
T=100, call a routine
T=543, Start over...
Hi,
In the BLE_UART example code posted here , I noticed a discrepancy with the SD 3.0 migration document, SDK12, and the example code.
In stock SDK 12.1.0, ble_stack_handler_types...
Hello everyone, i need some help and suggestions in understanding what is exactly happening. I have read a lot about bugs and workarounds in pstorage and now i actually don...
Hi, when reading radio transmitter peripheral example, I got stuck a bit on radio_configure(). I got stuck because I can only get some brief from the corresponding .h file...
i m using nrf51.... first i have call WFI(); and device goes to sleep mode...and when press any switch on gpio so, wack-up again...so, may i know that.. how many way for wack...
i m using gcc toochain setup in windows for pca10028 devlopment kit... and load BLE_UART code inside it... and now i m add onother rtc code inside it.. but it's not work....
main.c hello sir.. i m place rtc example code inside of ble_uart code .. and i m using gcc tool chain setup for pca10028 bord... code complile sucsessfully... code not work...
Hello all,
I want to use a single bank bootloader with the ISP1302 Module (nRF51822 Chip) and S110 (V8) Soft Device, SDK 10, for application update
Can I use the BLE...
when i use nrfjprog.exe download my application code,Change nrfjprog.exe --eraseall --program ble_module.hex --verify --reset to nrfjprog.exe --eraseall --program ble_module...
My apologies, but I just want someone to give me a quick brief on what are these things and how they work. AFAIK, the nrf51xxx series SoCs render limited, sporatic radio availability...
Hi,
I am Working on a BLE application in which I do not want to expose certain services until I am securely paired/bonded to a valid device. The problem is that during...
Hi,
I'm trying to use sd_ble_gattc_characteristics_discover to figure out which characteristics are in a service.
On the whole it seems pretty obvious (keep calling...
I'm using the nRF52 + SDK11.0.0 + s132 and the ble_hrs example. The function conn_params_init() is called to initialize the connection parameters that the peripheral will...
