I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi,
I made simple command shell via UART. It works fine when I type commands in terminal by hand. But I run into troubles when BLE chip is fed from MCU that send characters...
When I connect my ble mouse to the PC win8.1 , media button works normal.
When I power off and power on my mouse, it reconnected to win8.1 PC quickly, sensor ,left button...
I'm using the nRFgo motherboard (nRF6310 together with the PCA10004 Cpu board. I'd configured the nRF51822's Uart to 1 MBaud).
Is the RS232 level shifter (which is part of...
It's this will be work?
// Initialize the Bond Manager.
bond_init_data.flash_page_num_bond = FLASH_PAGE_BOND;
bond_init_data.flash_page_num_sys_attr = FLASH_PAGE_SYS_ATTR;...
Hello：
I need to ask you after the next programmed into how this routine testing 。（nrf51_sdk_v4_4_2_3355\nrf51822\Board\nrf6310\ble\ble_app_alert_notification ） The iphone...
Dear Developer Zone,
I am working with nRF51822 and IOS.
My device can only be connected to one central, so to one iPhone. To refuse connection from others centrals...
Hi all,
I've got some questions about the DFU OTA Nordic example (nRFToolbox):
What is available full stack update or profile update?
Firmware flow, does it need to...
Hi Folks,
I'm running into a problem with the pipes on my nRF8001. After I issue a Connect (0x0F) command, I receive:
CommandResponseEvent (0x84)
ConnectedEvent...
We have setup the RX and TX modes for ANT+ in Advanced Burst mode.
The setter function works (can confirm that by using sd_ant_adv_burst_config_set());
However when...
Hello,
I understand that S310 stack currently supports Ant+ and BLE peripheral. Is there any way to incorporate BLE central (S120) and Ant+ (S210) stacks on the same device...
Hi,
I have nexus 4 smart phone with nRF Master Control Panel application. How can i change the IO capability of the master device? I need to test the pairing process (passkey...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi There,
We are using two microprocessors in our project is kind of activity tracker which is stm32l (M3) with accelerometer, temprature sensor and SPI flash connected...
I'd like to start developing with the nRF51822, and have found the two kits supplied by Nordic, the nRF51822 Evaluation Kit and the nRF51822 Development Kit. What's the difference...
