Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Dear All,
I am trying to use sscanf in a project and I am getting the message that it is undefined. I am including <stdio.h>.
I cannot understand/find the reason of...
Hello everyone,
I'm taking the "Bluetooth Low Energy Fundamentals" course For all the examples I followed in the training, from what I understood, we loaded the peripheral...
Hello, we are trying to use the shell over bluetooth but in default it also uses the uart contorroler of the board. us there any configuration option to disable the zephyr...
I have not messed around with devicetree much before this point. I'm trying to create a custom dts and bindings for my device. Within my custom dts file, I reference the nRF52833...
I am working with nRF52840 with MAX86141 and learning how to setup the SPI connection
Here is an opensource example : https://github.com/JON95Git/zephyr-spi-directly
And...
Hi Support Team,
I am using the nRF7002DK board for our product POC (Proof of Concept) purposes. We plan to use the same MCU, the nRF5340, for our final product.
I have...
Hello,
I am using an nRF9160dk with the nRF52840 acting as the BT controller running the Bluetooth: HCI low power UART sample ( https://developer.nordicsemi.com/nRF_Connect_SDK...
modem_info_get_current_band expects an uint8 pointer to store the band into, but scans for an unsigned int (probably above 8 bit) in nrf_modem_at_scanf. This leads to memory...
Hello
I am working on a WiFi application using a custom board equipped with both the nRF5340 aswell as the nRF7002. When requesting a WiFi connection using the net_mgmt...
I'm using 2 nRF52840 DK to run a data transfer test between a central and a peripheral.
The Central device uses ble_app_uart_c, The peripheral uses ble_app_uart. These examples...
We are trying to re-layout the PCA10059 Dongle. I would like to continue to use the existing USB bootloader .hex file for updates via CDC_ACM. One thing I am confused about...
Hello, DECT NR+ seems as a good fit for our product, however, current stack providers(Wirepass and Lynq) are not suitable for us. I'm wondering are there other companies who...
Hi i am currently using nrf52840 s140 sdk ver 17.1.10 using central uart and i need to add dfu ota code to it how can i add what is the required files to it we tried these...
Since the tickets are scattered, I will summarize the questions about nRF5340 Audio again.
Prerequisites
NCS version is 2.5.0. Raytac's MDBT53-1M is implemented on a homemade...