Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I am practicing the intermediate Nordic Academy online course, and I have a problem of the thread viewer.
I have enabled debug, I did everything strictly according...
I'm using a modified "HTTPS client sample" from nrf/samples/net/https_client in ncs v2.6.1 on the nrf9160dk board. The base example worked great and I am able to perform the...
Hi,
i use the nrf52833dk with ncs 2.6.0 and the official peripheral_uart example to test NUS. When i use my new Galaxy Tab A8 (Android14) and try to connect to the board...
Hello,
I'm working with the npm1300, and I was recently trying to implement sleep/hibernate mode. The datasheet states that before entering these modes we should check if...
Hi, we are trying to switch our nRF9160 project over to using HWMv2. We get a linker error that we are unable to solve. We think it is the combination between using our own...
Hello,
In my efforts to upgrade my project from NCS 2.3.0 (with Zephyr 3.2.99) to NCS 2.6.1 (with Zephyr 3.5.99), I'm running into various build issues with Unity unit tests...
Dear support team,
I created a UDP server using nrf9160 and SLM, but it seems to respond to external accesses automatically.
I don't want it to respond to ports that aren...
Hello, I've spend some time updating our nrf5340 application to NCS v2.7.0, including using the new hardware model and using sysbuild. We have a custom application that we...
Hi,
With zephyr's example : https://github.com/zephyrproject-rtos/example-application I am evaluating to add a sample clap sensor as a custom sensor into the zephyr sensor...
I was working with nRF Connect for Desktop version v4.1.1 for quiet some time and it was working good, Since each time I was prompted to update the software to the latest...
Hi, I am using a NCS v2.6.0.I created a custom zephyr project. Implemented custom ble service and added BLE DIS and BAS services from source. 3 out of 2 services working properly...
Hello.
I wanna develop customized bootloader using C.
There's two purpose for this.
1) Select application area : Slot 1 for main application and Slot 2 for new...
Hi,
Does the nRF52832 support the Connected Isochronous Streams (CIS) / Channels and Connected Isochronous Groups (CIG), either using nRF5 SDK or nRF Connect SDK?
I would...
Hi,
I am using direction_finding_connectionless_tx/rx sample, and NCS v2.6.1 for AoA. I made some modification on the rx side to stream I/Q data via serial port, and read...
Hello,
I am running into a problem with my Thingy:53 device where I am unable to load up the bootloader. I has the edge inpulse application working well yesterday, after...
