Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi Nordic support
We have ealier used your legasy SDK16.0 on nRF52840 where we where programming our device serial number in the UIRC area.
NRF_UICR->CUSTOMER[0-4] where...
Hello,
I am using the nPM1300 IC on a custom PCB with the nRF5340 + nRF7002 + nPM1300 configuration. sdk v2.8.0
I am trying to read the battery status (ADC value) via...
I have problems when I connect to my mqtt broker, it looks like it doesn't do a CLEAN_SESSION.. according to server logs.. I see when I connect to test clients ( pc ) with...
Hi, I recently purchased a nRF52840 dongle with the intention of creating a Bluetooth mesh provisioner with it. The first thing I tried was flashing the mesh_shell example...
Hi ,
Could anyone please with NRF9160-SIAA-B1A-R7 CAD Files (symbol, footprint, and 3d file) for KiCad ?
Thank you for your support.
Best regards, Mohamed Obaid
I'm using an nrf52840 on a custom board and send debug messages with printk to RTT. When mcuboot is added to the firmware it is no longer possible to read the messages from...
Hi nordic support Team.
I try to build blinking led example: nRF5_SDK_17.0.2_d674dde\examples\peripheral\blinky\pca10056e Load firmware for NRF52811 and NRF52840, i see...
Hi,Team,
I am developing Long Range and Pawr using nrf54l15-dk.
For the Long Range example I refer to E:\NCS\v2.8.0\nrf\samples\bluetooth\central_and_peripheral_hr and...
We previously used the nRF52832 (with Segger Embedded Studio) and implemented OTA updates for it, along with developing a custom APK.
Now, we are using the nRF5340 (with...
My nRF52840 DK needs to interface with a convential device using the data bus and address bus. The following diagram (P.27) from the nRF52840 PDK user guide.shows the data...
Hi,
I got a question on IQ Sampling with the direction_finding_connectionless_tx/rx example.
Settings:
Sample Spacing = 125 ns
Sample Sapcing (Reference Period...
Hi,
I have an nRF5340 DK, and my BLE project runs fine on it. However, when I flash the same code onto my custom board, bt_enable() returns error -11 , which seems to...
Hi
In the newer versions of nRF Connect for VS Code, the NCS and toolchain version can be configured per build-configuration.
Is it possible to configure the desired versions...
