Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi all,
We are running into a problem with our battery powered nRF52.
The nRF is continuously powered by one lithium cell. When the battery is very deeply discharged ...
Hello,
In our current design, our boards use P0.18 connected to an external watchdog to reset the nRF52840. We configure PSETRESET[0]/[1] to be 0x12 (Connected/enabled on...
Hi,
I am using Zephyr to do some action in a main loop and ksleep for 30 seconds. While in ksleep(), I can see that the consumption is 20ua. The board is a very small simple...
I have a Fanstel Evaluation board which can be programmed through 52 DK board, no problem there and i also have built a custom board using the BM833AF modules based nRF52811...
Hi,
I was wanting to know if this function has been changed since mesh SDK v2.2.1? It appears to not behave quite the same. When I call it, I think the mesh does not entirely...
I am currently working on sending some custom data using BLE nrf52.
I find the BPS format best suited for my application but I want to modify the systolic and diastolic...
I am adding dfu capabilities to my app on SDK12.3.
For that, I took the example on sdk12.3/examples/ble_peripheral/experimental_ble_app_buttonless_dfu and copied the relevant...
I am trying to modify the receiver an transmitter examples to change the default bandwidth on both the receiver and transmitter. I have looked through documentation without...
What is the communication distance of NRF52832 Bluetooth reference? Since nrF52832 is used for the first time, we are not sure about its performance. Is it possible to reach...
Dear Team,
I am try to customize the some of the parameter of HTS221 temperature and humidity sensor used in thingy52 board, However if I change any of the parameter then...
I am using the nrf connect desktop application on windows with a PCA10059, and have found the application to be buggy when receiving a flood of notifications, this works fine...
I've been logged in for about a week now, and still can't log out.
I left a posting about that almost a week ago with some "bumps" later on the "back stage" section, but...
Hi!
Can anyone tell me that isthere any app which logs data automatically into txt or csv file from nrf52???
I am getting data at nrf connect but every time i need to...
PCB : thickness 1 t(1mn), 1/2oz, 2 layer
The antenna was removed and the VNA was connected between L3 and C6.
The impedance was about 100 ohms.
The part value is shown...
We have a latest set of prototypes which use an NRF52840 on a Laird BL654 module.
On two of these protoypes the module is unresponsive. We are using a J-Link Lite module...
