I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
I've been using the Thingy:91 to communicate with some sensors. One of this sensors is causing us some trouble: sometimes the I2C communication with him seems to fail...
Hello
I would like to commission my Thread network but my Thread network is isolated (I have no wifi) but I have bluetooth which works in parallel to the Thread network...
I tried to use pin_change_example in SDK to catch Interrupts (at first line) but I'm missing lots of them, I don't want to use PPI mechanism I just want to run my ISR in time...
Hi All,
I have developed my application for the nRF52832 (SKD15.2) on top of the TWI sensor example. I moved from the legacy TWI driver to nrfx due to the data length limit...
hi ,our company is developing a product.the product have a nrf52832 and nb-iot module.now have one case: system start normal and mobile connected the ble,but the gap will...
Hi,
This is not a ticket!
I just want to share a simple application that I have built for the nRF52840 . It's a USB keyboard.
The example also shows how to handle buttons...
Hi all ,
I'm using SDK 15.0, working on ble_uart.c
I need to change the DEVICE NAME of the frequently.
Can you please tell me how to change the the device name and store...
Hello everyone and thank you for taking the time to read my message.
I am new to this Devzone and I am looking for an alternative to nRFgo Studio to program the SoftDevice...
hi Guys,
before i shoot myself can someone answer me this simple question .... for most.
In the segger embedded software nrf to sdk do i need to complete stages 1-4...
Hi everyone, I am looking for an external oscillator on the nrf52840 DK that can take its own power and is similar to a push button that can make a voltage change on the GPIO...
Hi!
My BLE peripheral needs to change its "static" passkey under certain circumstance.
However, when I attempt to connect after setting it, I get a PM_CONN_SEC_ERROR_PIN_OR_KEY_MISSING...
Hello everyone,
I'm trying to interface a NiceRF LN610 LoRaWAN chip to nRF52840 via UART. Initially, I tried communicating with the chip using CP2102 USB-to-TTL module and...
Hi,
In order to measure the RF power, I measured the RF power by radiating inside the RF shield box.
But there is something strange.
The position between the device...
Hi ,
I want to develop the firmware to read the nfc tag and read the sensor data send to the application via BLE I have read many post regarding nfc . Let me explain what...
Hi,
I am working on temp. sensor with nrf52832 dev kit for firmware testing and development and also using nrf52810 for product testing.
in my code, I merged twi communication...
