I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello
I have defined the SPI pins in the sdk_config of the ble_app_uart example and compiled the code after adding the dependent drivers from spis project as shown in...
Hello,
when writing content onto the CDC-ACM interface of the nrf52840, I sooner or later always end up in a Segmentation fault.
I'm on nRF52840 and using the SDK v16...
I'm using the nRF52840-DK evaluation software from Segger. I want to add NAND Flash support, so I want to add an SPI interface. I have looked at the example in nRF5SDK160098a08e2...
Hi，we had finished application development on nrf52832 long ago, based on nrf52 sdk 14.0(with softdevice 5.0). But now we get feedback which is a bug has been fixed on sdk...
Hello guys,
I would like to know something more about the scheduler whose implementation can be found under SDK_ROOT/components/libraries/scheduler .
Our idea is to apply...
1. I don't want to call the fds function when enabling or disabling cccd: pdb_write_buf_store, so I did the following:
2. I am in nRF5_SDK_12.3.0_d7731ad in the sdk Routine...
Hi There - I'm very new to electronic design and need help making a key design decision. Specifically I want to know that the performance will not be a problem when writing...
Hi
On some devices we see in the production a shortcut between the BT antenna and the P0.18 pin on the 52811. The cause can be extremely warm weather at the production facility...
Hello,
We are tweaking the TLS connection between nrf91 and mosquitto.
What ciphers does the modem support? Is there a list available?
Best regards,
Vlad
I want to send a byte on Nrf connect app upon receiving an GPIO interrupt using BLE_APP_UART code. I have configured pin P0.10 for the GPIO interrupt. I am using SDK15.2.0...
Dear guys,
I am implementing a module that monitors the battery voltage for our tracker device using NRF9160.
I do not understand how to set up two parameters for the...
Hi:
The urgent problem we are facing now is:
debugging hci_usb on Linux, how to set MAC address and send/receive files ? hci_usb fw : \ncs\v1.3.0\zephyr\samples\bluetooth...
Hi, I have no found clear steps to create DFU zip packet for old one softdevice S132 SoftDevice v2.0.0.
I try to build with nrfutil pkg generate but seems its working only...
Hi,
We are currently trying the Long Range (Coded PHY) on our advertised message, but we can't see any improvement (range of about 50meters). The range can even be smaller...
