Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hey,
Is it not possible to use any Bluetooth status codes for disconnection when calling sd_ble_gap_disconnect ?
for example this is not working (I do not actually disconnect...
Hi,
Similar as this issue
Our QA team found the nRF9160 device will hang when user pull out the USIM card then try to deactivate LTE.
The issue can be repoduced by following...
We tested this issue on serial_lte_modem sample on NCS 1.2 and modem mfw_nrf9160_1.2.0
1, Enable CSCON unsolicited report:
AT+CSCON=2
2, Activate LTE search and connect...
Hi,
My problem in shortly is when I have debugger connected to nRF5282, I always get hardfault after some time.
https://i.ibb.co/hZ3bZ1b/optionbytes-1.png
I tried...
hi .i use the pca10056 connect to th nrfconnect by usb .andr dun the app Bluetooth low energy.other 52840 device run the hex of \nordic
sdk\nRF5_SDK_16.0.0_98a08e2\examples...
Hello,
I'am working with a project and want to maximize ble throughput from ble thingy52 to a central device. I have used the ble sniffer with wireshark to see data transfer...
Hi Team,
i am working on serial LTE modem sample project trying to send at commands through serial lte link monitor, found that device is not responding to at commands...
Hi,
Recently I updated nRF Toolbox iOS to 5.0.1.
I'm mainly using this tool for writing application via DFU to nRF51822 board.
I was using .hex files for DFU but I can...
Hi,
I am working on a product based on an nRF52832 (SDK 15.3, Softdevice S112 v6.1).
For security purposes, I would like to restrict the pairing / bonding procedure to...
Hello, guys!
I am using master branch of nRF Connect SDK and want to use UART_1 module of nRF9160 SiP to communicate with external devices.
I used nrf9160_pca10090ns.overlay...
Hello, I am evaluating different printed antenna options for my Nordic design using nRF52 series ICs. The small size of the meandered antenna used in the nRF24LU1 USB dongle...
Hi,
I am on SDK 15.2 and NRF52832. I think that I am quite stupid because I do not succeed to be in Non-scannable non-connectable mode.
I tried few stuffs, change directly...
Hello,
I need to create an acl connection using bd_address and GATT client LE connection mode.
how to create ACL connection?
How to close ACL connection using connection...
Hi I purchased nRF52840-DK board recently. I'm able to connect it to Mac OS Mojave and I see that the LED5 is blinking every second. However none of the LED1-4 are blinking...
