I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Dear Nordic Team,
we have unstable communication with an Osram BT device through nRF52840. We got information from Osram developers the nRF52840 is the right device for...
Hello!
I have question about Direction Finding in nRF52811, Angle-of-arrival to be exact.
To begin with, I have a custom board with nrf52811 onboard and 8 antennas....
Hi
As far as I know, NFC supports peer-to-peer communication, so I want to know whether peer-to-peer communication can be achieved between two 52832 through NFC? Is there...
Hello everyone.
Iam working on a project where i need to detect a falling edge from a ADC (ADS1298) when new data is ready at a sample rate of 500SPS. I have the issue...
Hi Great Nordic Support Teams:
I'd like to know schedule of nrf9160 specification:
1.When will 9160 support R14 regulation in NB-IOT/ LTE ?
2.When will Nordic release...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) I ported UART into my code and it...
Hey all,
I would like to make a flexible design with ability to assemble NRF52832 or NRF52810 , both are pin to pin compatible ,
But i just wonder how to consider regulation...
Hello,
I am developing a capacitive sensing application with the nRF52 DK and Segger Embedded Studio. So far I have integrated the Capacitive Sensor Library Example into...
Hi everyone,
I am working on a project with the NRF9160 DK where I want to use the UART3 channel.
The issue is that I got compiling errors when I add CONFIG_UART_3_NRF_UARTE...
Hello,
I want to test the Thingy Mesh Provisioning Demo v0.7 with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo...
Hi,
I am using s140 v7.0.1 for nRF52840.
I found if I configure NRF_GPIOTE->CONFIG[0], then BLE will not work.
Which GPIOTE channels are used in s140?
Thank you.
Hello,
I need example code or guidance in how to receive eddystone advetising packets on the nRF52832.
In my project, I can send standard eddystone packets to a app...
Hi All,
I am new to BLE technology and I am working on nRF52840 and I have below queries.
1) I need to operate my device to scan and advertise both at the same time when...
