Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello, I am making my first custom board based on nRF52832. I have used a custom antena design (due to PCB layout I did not use reference design). That was the very first...
Hi everyone,
We need your help with a condition that we encountered in our prototype of a nRF52840 that use a ceramic antenna. Our current design is poor and we will have...
Hello,
We have the following problem with a custom board based on the nRF52832 and the SKY66112-11 PA LNA, running as a mesh node.
The SDKs used are nrf5_SDK_for_Mesh_v3...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
My queries are:
1) In code I just changed...
Hello,
I have queries on Sniffer functionality.
1) Using nRF52840 USB dongle whether we can sniff BLE 5.0 packets.
2) Using nRF52840 development kit whether can I...
Here's is my device profile:
Running on SDK 15.2.0
FreeRTOS
Custom board, based on NRF52840
Powered by a 3.5Ah battery
Using CLI utility
Using the following...
Hello, we are developing a BLE application using SDK 5.2 and softdevice 6.2.1 (we are aware this is old, but we still have to support it).
We actually use Keil IDE 5.10...
Hello. I'm reviving an old project (nrf51 and 12.3.0 SKD with sd130 2.0.1). Unfortunately bootloader is not working properly. It worked just fine at the beginning of the year...
Hello:
GPS and LTE can't work at the sametime currenty with 1.0.0 modem firmware.
You know that EMC test need GPS and LTE work at the same time.
Will GPS and LTE work...
Hello, I would like to utilize UART and NUS to both send and receive data using the ble_app_uart example as a starting point. I have tried connecting to the nRF52 DK with...
Dear All,
I am using UART read write operation along with the system off mode. So, usually nRF9160 chip goes to sleep and wakes up when it receives something on UART and...
Hello Nordic support team,
I'm working with NRF52832 development Kit. I want to transfer our firmware application (OTA-DFU) from nordic central device to nordic peripheral...
Hi, I am trying to get RSSI values using BLE module on nRF52840(pca20035). But I could not see possible way to get the RSSI values on Nordic Thingy91(nRF9160) Please map me...
hi all
i want porting qpc with softdevice. it need set SCB_SYSPRI exception priorities with PRIMASK bit or the BASEPRI register for critical section
can anyone give me...
