Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
Hello
I am trying to do BLE communication using BLENano2 (nRF52832) now.
Therefore, using SDK 15.0.0, we are writing a program with keil u5.
Since writing to the softdevice...
I am a bit confusing about this two mode settings. We plan to use MODE=BLE_2MBit on both TX and RX sides as it can give us about 2dBm sensitivity improvement on the RX side...
I need to transfer data from my ADC (analog to digital conv) on a custom made, nrf52 PCB to a mobile app via bluetooth. For this I integrated my working SPI data transfer...
/** * Copyright (c) 2014 - 2018, Nordic Semiconductor ASA * * All rights reserved. * * Redistribution and use in source and binary forms, with or without modification, * are...
Hi there:
I'm now developing a product with 51822 using the SDK10.0 . The product communicate with another chip through UART.
My problem is when the UART crash with error...
Hi all,
I have an application where I have a mobile app that communicate with up to 20 BLE devices. The BLE devices are RGB LED lights with push buttons and a sensor. I...
Hi.
I'm trying to use nRF52 as TWI slave.
I am using Segger Embedded studio for the coding part and nRF52840 PDK.
I wanted to use TWI between the nRF52840 board and...
Hello Helper,
I am currently running ble_app_uart on 2-3 nRF52 dongles that acts as a node and ble_app_uart_c on nRF-52 DK that acts as a central. While establishing different...
hi:
App <lightblue or nrf connect> (ipone6) connect nrf52832 failed .But using Android won't cause this problem.
Here is the log that failed to connect lightblue...
Hello,
I am using my own board with the NRF52832 device.
I currently have a NRF DFU bootloader programmed and soft device. I used it to download my own App using the NRF...
Hello everyone, I am starting with the NRF52840 dongle. I intend to use it for a Uni project because I'm gonna use it later for work (new product). Since we're using STM32...
Hi everyone! I'm a beginner with BLE. I'm trying to test Eddystone beacon. I'm successfully run "ble_app_eddystone" example in NRF52 SDK, and I also successful connect to...
We are doing some rapid prototyping using PCA10040 boards. I have a bench-top setup with a PCA10040, and some sensors. We want to place our sensors on an Arduino shield, enclose...
Hi there,
I just found an example, Experimental: BLE Multiperipheral Application, https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/ble_sdk_app_multiperipheral...
