Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi everyone,
I'm trying to evaluate the BLE mesh SDK, using the example of the light_switch.
I have the SDK15 and the the SDK_mesh v2 and I am able to compile everything...
I downloaded nRF toolbox android source code from github.com/.../Android-nRF-Toolbox but it can't be built successfully, could you advise how do I do ?
Hi!
When using BLE privat random address, we expect the BD-address to change every now and then.
When advertising with the nrf52832, we don't see the BD-address being...
Hi,
I am using sdk 14.2.0.
there is no logs in pwm_library example.
even though i add it,it's not working.
bellow lines are added in Makefile:
$(SDK_ROOT)/components...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to use nrf51822 as SPI slave and other MCU as SPI master. I am using spis_pca10028 example...
Hi,
I am using sdk 14.2.0.
nrf_gpio_pin_set(OUTPUT_PIN); this function sets the gpio pin to vdd.
nrf_gpio_pin_clear(OUTPUT_PIN); this function set the gpio pin to ground...
Hello,
I am using a nRF52840 with SDK 14.2 and I am trying to synchronize my "app timer" which uses the RTC1 with respect to an external client which is connected over TCP...
I downloaded the latest SDK(15.1), and how to advertising more infomation,more than 31 byte.
init.config.ble_adv_extended_enabled = true;
0> <error> app: ERROR 7...
Hey guys,
I am using NRF51DK board and SDK v12. I want to add MPU6050 library to fatfs example but I have some problems. When i add "mpu6050.h" to my project i get "Not...
Hi,
I'm using NUS service on nRF51822 with SDK 12.3 .
I want to secure the communication between the nRF and the mobile application.
So, I want to know the different...
NRF51822
SDK12.3
keyboard demo code
After each delete match at the PC end，None of the broadcasts are searchable。Then I Google the content like this。
I wonder...
Hello,
I am using NRF52840 in my System. We like the USB access on NRF52840 and would like to use it. However, I don't need BLE in my application. Can I leave the Radio...
Dear All,
i want to make a product which using nrf24le1 chip, but now i'm stuck on the antenna impedance matching issue.
i'm not very familiar with the antenna design...
I'm try to using Nordic 52832 board to send hexadecimal to the phone, but it still receive for ascii.
Using example\ble_peripheral\ble_app_uart code for sending.
