Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi, I was looking on Digikey and there is a device with the following code: NRF51422-QFAA-R7 V2
Does anyone know what the R7 V2 means? I think R=reel? Thanks
Hello everyone,
I have two nRF51822 (PCA10024) which I want to communicate, one is a peripheral s110 and working properly with a batery service and a custom service, and...
I am new to BT certification so my following question may be incorrectly stated.
We are creating a new OEM BLE module using the nRF51882-CFAC. We intend to sell this module...
Devzone,
I've been working on a central device based on the project 'ble_app_multilink_central' and have encountered an error originating from within the softdevice of...
In Bluetooth 4.1 spec they mentioned scatternet option for BR/EDR topology....not for LE topology...
is that option of connecting to multiple centrals at a time will applicable...
I need a BLE device that can broadcast codes/id to my android mobile app. Also, I need those codes be changed by once in a while by an admin app. Is this possible?
I'm unable to get any output when writing to the UART while using the s110 softdevice. I'm refering to the hardware UART. I'm not using bluetooth for serial.
I'm using...
Hello,
I wrote a firmware for my project, based on the UART over BLE example, so using the softdevice, establishing connections, etc. It works.
I'd now like to use a...
Hi all,
I can program and debug my application just fine when the softdevice is not used (initialized). Problem is, when I do use the softdevice, I end up in Hard Fauld...
Hello,
In our prototype (Embedded System) we want to use nRTF24AP2 with Chip Antenna, as W3006, for example.
Our questions are: where and how needs to be placed the Chip...
Hi there,
I currently have an nRF51 DK set up transmitting six 20 byte packets per 7.5ms, there about, to an nRF51 Dongle set up as a central. When viewing with Master...
Hello,
I would like to move on from using nrf_delay_ms().
I thought this would give me some first results, but It don't. Whats wrong?
//a
static void test_timer_handler...
Should be noted that i'm using nRF51822 breakout board and i have a lot of problems with its programming. And i'd just begun to write own topic about my problems with connection...
Hi,
I am playing around with the BLE_proximity_template on the Redbearlab BLE shield and an Arduino Uno. I uploaded the sketch and paired my Android Lollipop device with...
I'm a beginner and have been using library provided by the nordic to communcate with nrf8001. I read nrf8001 data sheet but couldn't understand how to use the aci commands...
