Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi all,
This is for nrf9160 with firmware version 1.3.1.
I 'm trying to read back the certificates and comparing with a known CRC.
modem_key_mgmt_read is able to read...
Our system is composed of a nrf5340, a QSPI flash, and a nrf7002 on single wire SPI. We are not using the network processor.
We are using Zephyr NCS 2.9 with sysbuild. We...
I am testing the Sleep idle current for the nRF52833QDAA module.
The module is nothing connected outside except the fundamental circuit as the attached picture shown.
...
Hello,
We have the nRF52833 included in a new PCB design. So far it works well using mcuboot and a UART interface.
I'm trying to get the radio set up and running, and...
NCS: v2.7.0 nRFCloud/utils: a2db3ffedbda237f9c1efb7a68ec2d270c346e56 Hardware: Custom Board with nRF9161 I am writing a provisioning automation (with robotframework), but...
HI
this is my pm_static.pmy
I added the following in app.overlay
After the compilation passed, there was no response when I flashed the device.
this is my...
Hii,
I'm using Distributer and target sample code for testing OTA in ble mesh. Using nrf Device Manager App I'm able to upload dfu_application.zip file to distributer...
I have installed the nRF BTLE Sniffer plugin for Wireshark to do some transmission monitoring between my PC (central) and device (peripheral). To test, I have a U-Blox NINA...
Hey! I am working with 2 nrf5340 boards(nrf5340 Audio-DK as peripheral and nrf534DK as Central) and am trying to send 12750 bytes of data at one second from Audio-DK to DK...
Hello,
I am new to BLE Mesh and working with Zephyr. However, I've found the supported BLE Mesh samples to be very helpful in understanding the protocol and the environment...
hello Nordic
we have a master version that runs with older ncs version of mcuboot, and it is running ncs2.5.0 based app.
we have a release version that runs with ncs2...
Hi I want to download nRF_DeviceFamilyPack.8.15.0 for my Keil project but I cannot download with pack Installer and manually. If I want to donwload this package from website...
According to the data sheet, the nrf54l05/10/15 has 4 power domains. And there is a low-power domain. I search through the entire datasheet for a few hours and still couldn...
Hi everyone, I don't have a lot of experience in BLE protocol. I always lost data when I transport data by BLE protocol. I can predict data lost in intervals, can you share...
