Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
I'm moving from NRF9160DK to a custom board, where it has no UART. I plan to just use RTT for debugging messages.
However, I found if I delete the section which defines...
Hi,
I build secure_bootloader_ble_s132_pca10040_debug example (SDK17.1) on SES 6.30.
The only modification to the project is excluding SEGGER_RTT_Syscalls_SES.c.
...
It is possible to addressing nodes using MAC address of the device in Thread network?
In topology: PC <-> Border router <-> Thread mesh nodes
which IPv6 (Mesh-Local EID...
Hello
I'm new to the nrf platform and wanted to try out the I2C functionality of my nrf5340 DK. The only example I could find was the Fujitsu MB85RC256V FRAM I2C example...
Hi,
We are nearing production stage of our project, and are looking at programming on a large scale. Using the nRF9160 we need to program the latest modem firmware along...
I have a broadcaster and a central device. The broadcaster beacons data every 60sec and goes to sleep, a configuration I have considered for minimal power consumption. Now...
During tests with a "User controlled PLMN selector with Access Technology '6F60'" one device stuck in a curious state:
nRF9160 SICA B0A mfw v1.3.3 CAT-M1, PSM: PTAU 24h...
Hi Nordic community:
Can we configure nRF52840 to support a 1.3 V VIO?
I see from the datasheet, after the internal regulator, what supplies to the chip is actually...
Getting an error from mcumgr and I'm not sure where I should start debugging this.
My environment:
nRF Connect version 2.1.0 Board: nrf52840 DK and nrf52832 DK Host: MacOS...
Hello,
I'm developing with nRF5280-DK, using Zephyr-OS with mbedtls for the cryptography, and I need to have DES and 3DES enabled by default.
I tried to set in the prj...
Hi,
In a ble_app_uart example I have problems to send long packets if the Android smartphone only accepts MTU sizes of 20 bytes. I'm using the nRF5_SDK_17.1.0, the S132...
Hi,
Failed to reset CS47L63 when swapping the role,
if use the configuration like this:
[ { "nrf5340_audio_dk_snr": 1050140236, "nrf5340_audio_dk_dev": "headset", "channel...
Hi Nordic team,
I am working on BLE central application that should discover a primary service with custom characteristic. I have added the UUID for the custom characteristic...
Hi, I need to make a small change one of the Zephyr git modules. At the moment my Git has a west.yml and imports the nrfconnect SDK; which in tern imports the nrfconnect zephyr...
Hi,
I want to use the blinky code to develop a product using a nRF52832
I download the latest nRF Blinky app code from Github and try to run it with the latest version...
