I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
Have been trying to run nRF9160 LwM2M client sample. A problem is that it doesn't appear to be initialising the modem properly, by trying to access the network when the modem...
Hi,
I am trying to build the 'at_client' nRF9160DK sample app on a Mac and getting the following error:
CMake Error at /opt/nordic/ncs/v2.0.0/zephyr/cmake/modules/zephyr_module...
I am having the same problem as in
Case ID: 244142
devzone.nordicsemi.com/.../nrf52840_dk-spi-configuration
I am using nRF5340.
The problem I'm facing is that...
I use this code " node cli create-and-provision-device-cert"
But I am using nrf9160 ,so therefore I change this code to "node cli create-and-provision-device-cert --dk ...
This should be so easy, but it isn't. I started with the Dev Academy Lesson 6 I2C example. I wired up a little board with an I2C eeprom, created an overlay file to map the...
Hello,
i found a few articels about it but none of them where helpfull for me.
I just want to use my nRF51822 Module from Raytac without an external 32khz oszillator....
I was having an issue where reading from SPI inside a timer handler always yielded 0xFF instead of the actual values. I tried to reproduce the issue with a simple test program...
I'm trying to do a firmware update over BLE.
Here's what I did: - I created a new application from sample "smp_svr" because I think that is where I can see how to do firmware...
I'm running on Windows 10 and am trying to connect to my BMD-350 development board with an NRF52832.
I've also attempted to execute this with Python 3.9 and 3.8 (both installed...
I'm using SDK17.1 and pca10056 DK board. I want to use app_sched_event_put for a very simple purpose. I start a one second clock whose timeout handler increments a static...
Hi
I have configured my project to have a Modbus RTU slave on UART1. When I poll the dev kit, using Modscan, I get frame length errors. I have checked baud rate and parity...
I am trying to figure out why my application is generating a hard fault. The hardware platform is nRF52832 and SDK is 17.1.0
In my experience, the generic Cortex M3 processor...
We are trying to integrate the STEVAL_MODEM_BG96 chip into the NRF52840 for rapid prototyping. Trying to interface nrf52840 with the STEVAL-
STMODLTE chip via UART. Connecting...
I used to have a dts file for sdk52dk_nrf52832 containing gpio1 references:
rts: rts_pin{
status = "okay";
gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
label = "TS pin...
There was a question when doing the multi-channel test of ANT. The SDK is 17.1, and the example is (ant / ant_ multi_ channels)，Encountered the following problems：
1、Example...
