I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am interested in transferring large data (>255) over SPIS.
My application requires that the nrf52840 is operated in SPI slave mode. To manage such transaction I have SPI...
Hi ,
I need using dimming server example to add FDS function. But I meet some unstable sitation.
The bellow is the log show how the issue happens.
sometingtimes,FDS...
I am developing a robot controller(Central, nRF51822).
However, I am having a problem with UUID.
And I am using the ble_central (s130 ble_app_uart) example.
The figure...
Hi
I am developing a bootloader for nRF52840 using SDK 15.2.0 and s140_nrf52_6.1.0_softdevice, that should support both USBD and BLE transports.
The first transport layer...
We are using NRF52840 with Softdevice 340 and several sensors connected via ANT and BLE. NRF is connected to STM32 via serial UART connection and use ANT serial protocol for...
I am using PPK to measure current. The system uses 2 CR2430 in parallel.
I observe that
1. When using the battery as external supply, the battery voltage drop to 2.5V...
I am using the original board. It does not have a 32kHz crystal.
So I want to use the built-in RC oscillator.
In addition, use the time example of nRF5_SDK_16.0.0. "NRFX_CLOCK_CONFIG_LF_SRC...
Hello,
I am using nRF52840 S140 v7.0.1. I have few queries on DTM functionality.
1) As per standards, we can do DTM test either by sending HCI commands or UART commands...
Hi,
Using Eddystone example I configured EID and TLM slots. I see in nRF connect app both EID and encrypted TLM(encrypted data, salt, MIC).
How to exactly decode the...
Hello,
we are experimenting with the Nrf52811 CTE feature and have a few doubts concerning the documentation. We program our experiments with bare-metal (no soft device...
Hi,
I am working on one business use case. The basic requirement is to monitor the outdoor air environment from different locations. I want to try out the initial things...
Hi,
For nRF52840 BLE, in the DFU (OTA) example (buttonless OTA):
../nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral/ble_app_buttonless_dfu
How scanning is done? Or where...
