I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi,
Because I wanted to add custom features to mcuboot, I had to use custom mcuboot.
I also used sysbuild for multi-image building.
The documentation tells me that...
Hello,
I am currently working with the nRF5340DK kit.
For my project, I need to incorporate some additional custom checks/code into the project's bootloader(MCUBoot)....
hardware:nrf5340dk
The above 45 pairs of IQ data are a set of data that I have received.The maximum amplitude of the IQ data I received seems to be only 128, which means...
Hi I am implementing dfu over modbus. Basically I managed to integrate all the steps (transport, set pending, restart, confirm).
What I'd like to do is to implement image...
Good afternoon,
I have recently purchased a PPK2. I have installed nrfConnect for desktop and Power Profiler on my Ubuntu 22.04 machine. I have connected the PPK2 and...
The example for LZ4 works fine, however I want to use the frame format and not block format.
Therefore I added #include "lz4frame.h" to my main.c and tried to use LZ4F_compressFrame...
My project is developed on nRF52840, it needs to communication with a mobile device through BLE, nRF52840 is as central. The mobile device starts BLE advertising, then, nRF52840...
hello guys, I want to use nrf52840 for my project is it possible to use ST Link for it. because I don't have SEGGER J-link ,if it is possible how can we use it please let...
Hello
I am trying to connect the nRF9160 -DK board to nRFCloud using CoAP protocol. I have written an application for this case. I tested my application with two different...
Hello
I'm trying to connect nrf7002EK with SPI3 with nrf52840DK,
NCS/Samples/WiFi/Shell, but I came up after Flash
The error shown in the image below
I would like...
Hello,
I'm trying to erase/read an external flash ( MX25L6433F) connected to an nrf52840 using nrfjprog. I've created a .toml file for the configuration, see attached. The...
Hello,
With the nRF5340 LE audio application comming with nRF Connect SDK 2.6.0, I found an increase in the audio latency compared to previous versions. I was able to measure...
Hi,
I'm implementing flashing modul, which will be running on external mcu. Therefore for the very 1st step, I have captured traffic while performing dfu on PCA10040 via...
Hello,
Do you have an example that allows you to use the “Service Changed Characteristic” on the server side?
In fact, I saw on the internet that on IOS, we have to use...
