Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hi,
I am using nrf Connected SDK v2.6.2 on windows 10. I try to create a blank application project for the device ADXL363 on SPI2 bus on the nRF9160DK board.
I basically...
Hi,
In the attached hello world example that I modified for the nRF5340DK board, the nRF UARTE serial driver doesn't exit low power mode when I type any characters on my...
Hi everyone,
I've been developing an application using the nRF7002DK, where the nRF5340 SoC communicates with the nRF7002 SoC to connect to a Wi-Fi network, retrieve a JSON...
Hi, I'm quite new with the nrf ecosystem. I'm trying to setup a nrf52833 development board to use an AHT20 as a humidity and temperature sensor. I tried coding my one i2c...
Issue:
The OTBR could run with RCP versions built with SDK v2.3.0 and v2.4.2 but couldn't work with fw from SDK v2.9.0. Hence, I wanted to know which of the latest SDKs...
Hello,
I’m trying to obtain millisecond precision on nRF Connect using the MCU’s internal RTC.
My code:
After 131000 ms, a got:
Could someone help me find...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
Hi, I am facing an issue while integrating BLE with the rest of my code. The code crashes when I try to start BLE outside of main() .
Currently, I have placed the BLE initialization...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
I'm trying to program an nRF54L15 on the nRF54L15PDK evaluation board with the DEBUG IN SWD pins (P15). On my setup I have a J-Link PLUS connected to P15 and a USB-C connected...
I have the following settings in my prj.conf:
and getting the error
CONFIG_FLASH_MAP was assigned the value y, but got the value n. Missing dependencies: FLASH_HAS_DRIVER_ENABLED...
Dear Nordic team,
we are facing a strange phenomenon - in idle mode (k_sleep(K_FOREVER)) we notice, that the current consumption drastically increases if a magnet is placed...
I have a production system running a modified asset_tracker_v2 sending temperature data to AWS. All is working fine with V2.5.0 on several hundred sensors. I am trying to...
Hi,
I am looking for procedure to make it work nRF240L01? I am getting documents for Arduino but as you know that is not understandable, with Arduino it worked but i don...