I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I'm encountering a blocking issue when trying to create a new board using the NCS Board Wizard in VS Code with Nordic Connect SDK v3.0.0. After filling in valid inputs and...
Uploading via VSCode since version 3.0.0 (happened with the rc1 as well, Toolchain 3.0.0 and Toolchain 3.0.1) does not work for the nRF54L15DK (board rev 0.9.1 ENGB chip)...
Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hi, I am using nrf52840 , nrf connect sdk 2.6.0 I am using spi_transceive() to send and receive the data from sensor I read in Nordic Academy nrf connect sdk intermediate...
I use SDKv2 . 09 . 00 without using the eSB function timelot can trigger MPSL_TIMESLOT_SIGNAL_TIMER0 normally，then NRF54L15 Running esb and BT at the same time with MSPL cannot...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
Hello, I have nrf5340dk and AT21CS01-STUM10-T module. This is EEPROM module. I want to communicate with it by 1-wire. The problem is that I don't know how to do it. I looked...
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board and a series of nrf52840dongles (provisioning and configuring inside the software and...
Hi,
I have a Thingy:91X which connects fine to hello.nrcloud.com. Now I want to connect it to my own nRF Cloud account.
Note that I have successfully provisioned multiple...
I am working on a project using the nrf9160DK for initial firmware development. Trying out the SAADC i encountered that the measured values were always about 20% lower then...
Dear Nordic Team,
I hope this message finds you well. We are currently using the nRF9160 in our product and have a few questions:
Can you confirm the ongoing availability...
Hello all,
I am having issues with the configuration of the FEM nRF21540 on the costum board Fanstel BT840NE with the Enhanced ShockBurst (ESB) protocole.
We are not able...
I'm currently working on implementing OpenThread on our custom board based on the nRF5340 along with the nRF7002. While building the project, I'm encountering the following...
Hi all,
I'm working with my custom nRF9151 board and i'm testing https request with option that use native TLS for my download client.
I got connect err = 22, so i come...
Hi, With this setup in , I successfully built a CIS mode using my nRF5340 DKs , enabling stereo sound while the microphone is active .
However, I am currently experiencing...
