Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hi,
My nRF52840 dongle which was working fine in the past doesn't seem to be responding properly. Is there anything I can do?
Some background:
1 - I have used it...
When we test the matter, we sometimes will meet commissioning accessory fail and network dropping. In the worst case, we can't access the network for a long time after the...
NRF_SO_RAI_NO_DATA AT#XSOCKETOPT=1,50 does not cause RRC release as expected, instead hipower LTE continues another ~20s. https://github.com/nrfconnect/sdk-nrfxlib/blob/main...
nRF52840, SDK 17.0.2, SD140 v7.0.1
My firmware application is happily sleeping via calls to nrf_pwr_mgmt_run(), waking up to service interrupts and do work, then going...
I have not been able to get the nRF52840 ncs v2.0.2 watchdog not to reset.
I tried kicking the watchdog every second and can set a break point and see that the kick does...
Hi all,
I'm looking for an SDK function that will tell me if my device is connected to BLE
from this post 8 years ago the answer is no, has something changed in those...
I am using the 9160 to develop a product for the customer. Its sdk version is ncs1.9.0, and the firmware version of the modem is v1.3.1. The device needs to download data...
Since sensor.h API in Zephyr does not support reading hw FIFO, I am planning to use SPI driver to read the hw FIFO on received an interrupt when FIFO has data.
Is there...
Hello
I use nRF9160DK.
Can somebody tell me why it doesn't give an error ( ) if I don't have anything on the I2C line, or how can I be sure if it finds the right address...
I've tested the TX power of nRF52840DKs using CLI application and a sniffer (sniffer device is nRF52840 Dongle). Sent message from one DK to other one via UDP and observed...
Hello,
I am trying to implement the Y-modem protocol to the ble_app_uart example. Basically, I want to send a file from the PC and receive a file in my nrf522840 device...
I use SDK16 with softdevice. Some of its features require hard timings. But it causes hardfault sometimes. It happened at function of gcm_init. My source code is as follows...
Hi
Is there any software that allows to save received Bluetooth data to a spreadsheet? I am using the nrf52 DK running the ble peripheral uart example and received the data...
Hello, after upgrading to SDK version 2.1.0 I noticed that the compilation of all my projects for actinius_icarus_ns always fails:
This is even for projects, where...
