I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi:
I use sdk:nRF5_SDK_17.0.2_d674dde and NRF52840.
Reference examples:nRF5_SDK_17.0.2_d674dde\examples\peripheral\uart
PC connection RX-pin20 and TX-pin22, PC sends...
Hi,
We are looking to purchase the nRF52832 SoC. The data sheet says it supports a data rate of 1Mbps when the receiver sensitivity is set to -103dBm. This data rate is...
I am experiencing a strange behavior with SES 6.32, using GCC and I wonder if I should choose a different compiler.
COMPILING THIS PART OF CODE (I added line numbers for...
I want to add wifi connectivity to asset_tracker. It is required that MODEM is turned off. The program flow need to change so that instead of Modem, wifi Module is tried first...
Hello,
I am trying to read a 32-bit value over BLE but the value displays as 8-bit on nRF Connect. In my code I am sending it as an int32. Why does nRF Connect only show...
Hi There,
I have almost done the project, I used nrf52832 as central(master) and nrf52810 as peripheral(slave).
i use the blinky example and everything working fine. I...
Hello,
I am using nRF52840 and I currently am working on a application where mostly I am using central functionality (BLE connection and exchange the data) along with cellular...
I'm willing to use the 5 claused licensed code for the parts that only work with nordic hardware, but the partition manager isn't actually necessary. Is there some way to...
Hi,
I am trying to migrate a moderaely complicated nrf5340 app from sdk 1.9.1 to sdk 2.0 and having a few issues with getting the right crypto configuration. Original...
Hello, guys！
I'm currently just starting to work on the nrf9160dk board. I want to try to explore the communication of nrf9160 with external acceleration sensor. First,...
Hi Team,
Is there any blog/tutorial on how to add custom profile (service/characteristics) with ncsv.1.8.0 and nrf52832/33?
I could find a couple of blogs but they were...
Hello everyone, I'm testing the example ble peripheral "UART/Serial Port Emulation over BLE" with SoftDevice S112 nRF5 SDK v17.1.0 . My board is MBN52832DK and i'm using the...
Hi,
in my project I use the nRF52840 microcontroller as the master I2C device.
Sometimes the TWI peripheral SDA line is forced to a low value by the slave device. This...
