I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi, am I able to communicate over mesh with long range (coded phy) and simultaneously communicate over GATT (say to Android phone) using 1M phy? If so, could you point me...
Hi,
We are switching from vanilla zephyr to NCS and would like some directions about support for zephyr LTS2. Can we expect Nordic to keep patches to NCS 1.8.x tracking...
I had described my problem in my previous question .
In short, after a long time of a bunch of central BLE devices regularly connecting and disconnecting to my nRF52840...
I've did my homework and googling but got more confused than ever.
Basically I'm trying to printf to the debug (printf) viwer window to help me demonstrate certain information...
Hi Everyone,
Hope you all are doing well.
I'm using nrfConnect sdk v1.7.0 and vscode for development.
controller : nrf52833
Here I tried to build image with bluetooth...
Hi. I have been using this document to work on the Fanstel USB840F device. USB840F_User_Manual (squarespace.com) After erasing the device, I could'nt run this below command...
Hello, I am developing a custom board using the nRF52810 WLCSP package. I realized I made an error in the board layout after placing my order, the error being that I placed...
I made a DFU Bootloader for my nrf51822 that waits for two seconds before starting the application, so I have time to connect and flash.
That process was working with the...
If I set two separate UUID scan filters as below:
Is it possible to discern which event triggered the filter match?
At the moment on the scan_filter_match callback,...
Hello,
it's a nice concept to include sensors via the device tree and simply enable them in the project file. But I feel like I'm losing control of the sensor a bit. I don...
Hello nordic. I've been using the PPK2 to measure the current draw of the nRF9160DK. However, spi peripherals are not included in these measurements. I was told that if you...
Hi
I´am pretty new with the nRF connect sdk. I want to check the features from BLE long range /coded phy.
In the past I have allready worked with the ble_att_mtu_throughput...
hello Sirs
How can I put nrf5340-sdk in to extended mode to transfer 250 bytes of data over BLE radio?
the sample code I am using is Peripheral-uart example code.
Excuse me:
I want to implement nrf52833 run FreeRTOS，The nRF52840 project in nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hrs_freertos\pca10056\s140\ses can only...
