I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi all
I am using nrf52840 kit, and I have a simple BLE app(client/central that turn LED on to a connected server/peripheral) running on it(sdk 15.3). Now I want to put...
Hi,
I'm using nrf gateway application in android and it is not able to connect to nrf cloud. I have reinstalled it but still the it say 'Gateway connecting...'. Please...
To the kind attention of Nordic support team,
Is there any update about this topic:
https://devzone.nordicsemi.com/f/nordic-q-a/59738/usb-device-suspend-resume-issue...
Hello, I managed to run nRF5340’s QDEC on development kit. The dts overlay looks like this
The problem is I do not see the LED gpio (P1.13) switching on and off on the...
The datasheet appears to say that a pin_reset does not completely reset the chip:
in particular it does not reset the SWJ-DP interface which, I believe, in some circumstances...
HI,
I'm developing it using NRF52832.
It is intended to update the remaining battery capacity through the battery_level_update() function by receiving the battery measurement...
Hi,
Few Binding APIs are absent in nCS as compared to nRF5 Mesh SDK. Compiling some models for certain boards is generating compile time errors, is it that certain models...
Hello! I am currently looking at options for unit testing frameworks ( for TDD and CI/CD) on host OS(Windows preferably but Linux if I must) for nRF8233 core custom boards...
Hi,
We need to save 3 strings to flash using NVS. Based on the code sample in zephyr\samples\subsys\nvs we set the initialization and then write and read these data.
To...
Hello,
This question has been asked - but that was awhile ago - some could say in an almost different landscape than what's going on today - so, please don't answer this...
At 1M rate, test the reception sensitivity of Bluetooth chip, the number of packets lost at -90dBm exceeded 30.8% as specified by Bluetooth Alliance, and this situation occurred...
Hello,
I am trying to figure out a problem with the WDT module behavior
Running on an nrf52832 and using SDK 11 with softdevice s132 v2.0.0!
There are 3 WDT channels...
Hi,
I have nRF52840 DK with Power Profiler PPKI. It was working for long time, but now it suddenly stops working.
Screen saved:
nRFConnect Dektop version 3.7.1, Power...
After I changed from SDK 17.0.2 to SDK 17.1.0 I get for the example project "blinky_FreeRTOS_pca10040" during the compilation with IAR Embedded Workbench IDE - Arm 8.50.9...
Hi, I had designed custom board using icm20948. i tried to get raw values from sensor and succeed then i had ported nucleo code for nrf53 zephyr. when i tried to run below...
