I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi,
I have successfully done one publisher and one subscriber example by using mosquitto broker on raspberry pi and 2 nrf52832s. What I want to do is that I want to send...
Hello, I have a very basic question:
Are Bluetooth nRF5x products compatible with other manufacturers? For example, can I have an nRF51 dongle communicate with a Microchip...
There are two APIs in SDK 14.2 to access the nrf52832's AES core. What's the difference in behavior between the two?
I noticed that nrf_ecb_crypt() has a useful return value...
HI:
I Select the SDK11 as my BLE master.
" nRF5_SDK_11.0.0_89a8197 \ examples \ ble_central \ ble_app_multilink_central \ pca10028 \ s130\arm5_no_packs ".
I Select the...
Hello,
I use NRF52832 and nRF5_SDK_15.2.0 for our custom board.
Also, FreeRTOS(Tickless IDLE is enabled) is used. And, System ON mode is used for sleep mode.
Now,...
Hello,
I am trying to send data from nrf51822 through UART TX to esp8266. I've gone through the app_uart examples and I can recieve data through RX but having difficulty...
Hello,
First, I follow this tutorial --> https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial . It's working well on the...
Development Environment: Segger Embedded Studio 4.16
Debugger: Segger J-Link Lite/ Segger J-Link Pro
Debugging a custom nRF52810 board using SWD interface.
I am experiencing...
hi
i create mesh network using the light switch client/server every things work well!
i have number of client and only one server.
i set the server to subscribe to the...
Hi,
i'm trying to sort out a performance problem I have with Android clients connecting to my nrf52832 using ble_nus service. Notice my problem is not about the absolute...
I am successfully using the ZigBee OTA upgrade example, but the firmware upgrade takes quite long, approximately a half an hour, so it is not an adequate time at the firmware...
Hi,
I'm using nRF52840 with SDK15.0.0 wit code from : https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial
I could make...
Hi there! I'm an engineering student who is just getting started with all the ARM SoC's and BLE environmenment, in order to develop a project for college. The project that...
I try to test Relay performance of BLE mesh, my setup as following:
1 one client loaded light switch client;
2 two server loaded light server with Relay On;
3 one sever...
