Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
According to the Online Power Profiler , the Standby time between Crystal start-up and Start radio is ~1 ms; however, we measure a variable amount of time between 0 s and...
HI All,
i m new to this technologies.Now m using NRF52840 DK and sdk as nrf15.2..we have developing the nrf52840 as a beacon scanner to scan the ibeacon details like rssi...
I'm using a Nordic dev board (PCA10040, nRF52832) with modified "Nordic_HRM" firmware sending packets of 20bytes at 100Hz over Bluetooth Low Energy.
I'm using Nordic's heart_rate_collector...
Hello everyone! I have followed the tutorial " Installing a 6LoWPAN enabled Linux kernel and required modules" and i have compiled the UDP client IoT example in order to test...
Hi everyone,
I am using nRF52 which has 52832 on it. Currently, I am working on 2 nRFs and one RPi with MQTT on the softdevice 132. One nRF is the publisher, another one...
I am using pcaboard10028 ,sdk12.3.0 and softdevice s130. I am using proximity example to read battery percentage level,so giving adc input as following:
channel.config.config...
Hi, I'm having problem with UART communication. I use basic UARTE code and I want to send simple data to PuTTy terminal. The problem is whatever I would send i get only 'K...
Hello!
I'm trying to update the bootloader of a nRF52 device OTA. We are using SDK 12.3. The device has our own application flashed, along with what is essentially the bootloader...
Hi Sir,
We want to know about AoA /AoD applications for 52811, and there are some question as below.
1. Is there a difference between BT 5.1 and BT 5.0 from the perspective...
Hi,
I'm implementing quadrature encoder to read motor speed/position. So far I configured a gpio pin where A channel of the quadrature encoder is connected to capture timer...
Hi, I'm now using nRF52DK with Keil and have followed the getting start manual in the Nordic Devzon.
Till now, I completed UART example and want to add ADC function to this...
Hi,
I wanted to know what is the recommended way of data transfer through ble if there are multiple sensors. Is Creating one service with multiple characteristics a good...
Hi everyone,
I am using SDK 15.2 with keil microvision and softdevice132 nrf52_6.1.
In version 13, system dispatch event was regestired with Softdevice handler as below...
