I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
I have spent several months researching and experimenting with creating a working nRF Connect SDK environment in Windows WSL, and finally have everything configured flawlessly...
I would like to monitor the states of switches sw0 and sw1 on my nrf7002dk board using GPIOTE interrupts.
Initially this is just for example purposes.
I eventually need...
sdk: 2.5.1
cpu: nrf5340
I have a bootloader which have a big ram block for upgrade purpose (around 250kb) in bss section (I will move it in noinit, but it is not the point...
Hi,
I am using nrf52840. we have already used 3 SPI instance (SPIM1, SPIM 2, SPIM 3). wanted to use one more SPI instance i.e. SPIM 0. but if I enable this I am getting...
For our project we switched over to using DIRECT_XIP mone primarily because of the faster boot time but it automatically enables downgrade protection. For our project we need...
Hello everyone,
I'm actually making some research for an internship about the last generation of Nordic's chips : nRF54 and I have many questions that i got after making...
Hi,
TWIM does not work well with nRF5340DK as shown in the subject. The conditions are shown below. - I/O voltage is not 1.8V. The waveform is distorted around 2.5V, though...
Hi,
We are developing a device using the nRF5340 DK and need to add external Flash memory accessible via QSPI with XIP, as the available memory is insufficient due to DFU...
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
Hi all,
I am very new to the nRF controller. Previously, I have worked with STM32 controllers.
Currently, I am working on a project with the nRF5340. I am having difficulty...
Hello,
In the past, i have posted a ticket to ask can the CIS and BIS modes work simultaneously. The answer is that it is feasible in the future.
Can CIS and BIS modes...
Development Software: Segger Embedded Studio, nRF5_SDK_17.0.2_d674dde
Project consists of an nRF52DK-based peripheral (remote control) and a custom nRF52832-based central...
Hi,
I have a project that uses nRF5340 with MCUboot and multi image update configuration. The update works, but today I noticed that the pcd_sram RAM region seems to be...
Dear Support Team,
Hardware : nRF5340 Custom board
Software : nRF Connect SDK v2.2.0
I have implemented OTA FW update for nRF5340. I've used multi-image simultaneous...