Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hi Dear
Is the WLCSP package of nRF54L15-CAAA a glass package?
Is it similar to the WLCSP package of 52832-CIAA?
The above refers to the molding material.
If possible...
Hi Nordic
What is the best way to protect against downgrading the APP FW via DFU.
I seems that im able to downgrade even 2 config below are set.
I tested it on SDK...
Hi,
I have two PPK2 units, and under the exact same test environment and PPK2 settings, simply swapping the PPK2 results in completely different measurement results. Which...
Hi all,
I'm trying to combine two NFC messages, I know that I can combine multiple records into one message. But the problem is that OOB_LE message will already contain...
I'm fairly new to Zephyr and initially I'm hoping someone can point me to an example where SMP over UART can be used to update a firmware image slot. Google seems to have...
Dear All,
We need to develop a custom low-level driver for NFC communication using the Hardware Abstraction Layer (HAL) library exclusively . We are currently unable to...
Was able to build after I installed these two packages
/usr/local/opt/python/libexec/bin/python -m pip install --break-system-packages PyYAML brew install pykwalify 2>&1...
I only learned today that the REGOUT0 voltage is changeable, which could be perfect for us, because our power needs changed dramatically.
Our circuit was originally designed...
I ordered a Thingy 91x and am tyring to configure it according to Introducing the Thingy:91 X – The Ultimate Cellular IoT Prototyping Platform on YouTube but I am getting...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
Hello, I'm a beginner and trying to do my project with nRF9151DK. As said this project uses the nRF9151DK that requires high-throughput USB-UART data streaming on two boards...
Hi,
I am new to arm and ble development. I am used to work with AVR mcus and I am trying to migrate a project from AVR to nrf52.
AVR usually has some "General Purpose...
Hello, I would like to evaluate the Thingy 91:X, but I can't install nRF Connect SDK on any machine (Windows / openSUSE) due to various problems. I will try to break down...
Hi,
I'm trying to power the chip on the DK from 5V power supply. I connected the USB connector J3, and switched SW9 to "USB Source". However, it seems that this is somehow...
My design is in alpha test and we just discovered that apparently SPIM allows only one module to be enabled at a time. When a second module (SPIM3, SPIM2) is enabled, the...
