Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
I'm developing a project, where I use nRF9151 as a GPS sensor, and nRF52833 as a BLE gateway. I want to send data from 9151 to 52833 over one of UARTs. The problems I'm facing...
Hello,
I’m currently working on a hardware design using the following components:
nRF54L10 SoC
nRF21540 Front-End Module (FEM)
2450AT18B0100001E chip antenna...
I'm developing a project for nRF54 using NCS. I have a question regarding the placement of the BLE protocol stack. In the previous nRF5 SDK, the protocol stack was usually...
I have downloaded the nrf connect software and downloaded the segger drivers. I cant see the drivers in mi windows drivers administrator. The evk is powered by the usb because...
Hardware env: New designed board with NRF52840 + NRF9151, which 52840 connect 9151 via uart
Software env : NCS version: v3.1.0 (new installed) Nrfutil version: 8.1.0 (34e21a1...
Hey, since iOS version 18.6.2 the BLE connect to our BLE peripherial with nrf52840 getting disconnect events. Also the range between them is very bad. The connection parameter...
I'm currently working on some projects for the nRF54 platform using NCS and VS Code. I want to delete the unused files in my project because the codebase has become too large...
In the nRF52840 Product Specification PDF v1.11, on page 323, the third paragraph down states:
1. "If the CPU performs a clear operation on a bit in the LATCH register...
Hi Team,
below mention errors I am getting west build process.
* Executing task: nRF Connect: Generate config HVPP_BLE_Board_Files/nrf54l15/cpuapp for c:\Haritha\Github...
hi support team，
customer told me 54L15dk debug out is not able to program another 54L15 chip.
so i tried,
1. A-54L15dk debug out program B-54L15dk debug in, failed...
I'm trying to leverage the asset tracker project form nordic 9160dk to actinius icarus 9160 board, i use tagconnect 2030 to connect P19 of dk and icaurs, but the jlink cannot...
When I try to add OTA image compression for MCUboot, the RAM utilization skyrocks and is not compatible with the nrf52833. Is there any way to cut out any and all excessive...
Hi, I'm working on a product that uses nRF52840 (The custom board actually has the Ebyte module E73-2G4M08S1C). nRF5 SDK 17.1.0. The firmware consists of: 1. Bootloader -...
