Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a.
Here my application sends 240 bytes of data every 150 ms. But after sending few...
Hi,
I use the a gpiote_in_event to trigger a number of PWM pulses which works fine so far. However, the exact behaviour of the generated signal is important so that the...
Hello, I am using nRF52-DK with Segger Embedded Studio and I'm running the following code that first blinks the LED1 on&off 5 times, and sets up BUTTON1 for wake up, and then...
Hi,
I would like to read the temperature of the nRF.
I tried to use the routine I found here in the forum
Sometimes works sometimes the system crash. I notice the...
Hi
I am using NRF5340 chip in my custom board to communicate serially with an external device whose data length is more than 128 bytes.
The chip can receive 243 bytes...
I am looking for the examples for the SDK. I installed SDK 1.9.1 through the Toolchain Manager and see the directory "users/my_user_name/ncs/v1.9.1" Supposedly this is where...
Hi,
In Openthread's Coap_client sample, Following 2 libraries are there:
and while compiling my code I get multiple warning regarding to above 2 libraries.
Following...
Hi,
I have problem to use bmi160 library with nrf5340 in spi connection.
I use the example application zephyr/samples/sensor/adxl372 and change the sensor to bmi160 (...
Hi DevZone ! Here is my issue: I use to work with VSCode and nRF Connect for desktop for a few months now. Early on Monday, I did uninstall all my dev environment (VSCode...
Hi,
is there any way to get a Pin to a defined "high" without vdd-gpio ref?
In our situation the NRF9160 Power is a Battery with 4,1V and the VDD-GPIO is 3,3V with a regulator...
I created two build configurations a Debug and a Release in SES IDE.
Build > Build Configurations...
I wanted to select the DEBUG_OPTIMIZATIONS level for the Debug build...
This is a continuation of the topic here that is now closed
https://devzone.nordicsemi.com/f/nordic-q-a/85590/nrf9160-azure_iot_hub-change-dps-username-during-run-time ...
Hi, I want to update the modem firmware devices(in the field).I am using nRfconnect sdk 1.5.0 and hardware is brf9160 SICA B1 . current modem firmware is 1.2.3 . I tried to...
I tried to define an event as in attached figure. During Build, the error in the as shown in the attached imageoccurs. Where to define Log Configurations ? I ading custom...
cpu info:nrf5340
software:nrf connect sdk 1.6.1
hi professor,
In the uart interrupt I call k_fifo_put to trigger rx process thread but it is not take effect.What person...
