I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi community
In order to set a reasonable CONFIG_MAIN_STACK_SIZE I'd like to have a stack usage report.
I've seen the option CONFIG_STACK_USAGE . This generates an additional...
We read 3.6 V using the ADC, for our mass production devices. The error rate is about 50% of the devices show wrong values between 3,05 and 3,4 Volts.
Even though the ADC...
Considering nRF52810 for a new project with a dead-simple application. Background:
- application is just data-pipe from mobile app to UART, both ways. No encryption/decryption...
Hi Team,
we are using the I-Jet Debugger with IAR IDE , How to load the Bootloader with this setup. Is there any additional settings required for this like Segger J-Link...
I have created code in GPIO read/write code with zephyr os. I did not add GPIO in .dts file. How the my GPIO example is working.
GPIO driver is not needed .dts support ...
Hello, All,
I am using the nrf connect tool on VS code for development, but i have a questions:
The west and some other python plug-ins used by this tool are installed...
Hello everyone. I am trying to develop a communication link between two nrf52 devices. I want to collect measurements from some sensors, pack them into a single data pack...
Hello,
I'm running Buttonless DFU successfully, but I would like to know if it is possible to start the application with the DFU service disabled, and activate it only later...
Hi, I have a firmware that runs well on nRF52833 dev kit (SDK 17.02) and I am trying to port it to a Laird BL653 dev kit. The firmware has a bootloader and it can perform...
so I use the default sdk in
D:\sdk\nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c\pca10056\s140
when i press button on nrf52840dk(pca10056)
it should at...
Hi,
I am evaluating the nRF5340 SoC and the recommended toolchain nRF Connect SDK (NCS).
I see that NCS is based on Zephyr RTOS, which provides also some drivers (spi...
Hi! I'm trying to save some variables after a watchdog reset for debug why my application hangs up.
I add a ram section on flash_placement.xml ( <ProgramSection alignment...
I am looking for Static analysis tool ( which is in compliance with standards MISRA-C and CERT-C) to be integrated with Segger Embedded studio.
Is there any preferred...
Hi
I am looking for a ways to perform DFU over serial, surprisingly i dont find any ways except this thread with no answers
https://devzone.nordicsemi.com/f/nordic-q-a...
