I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Good morning,
I'm working on nRF5 SDK v17.0.2 and I am using Segger Embedded Studios (SES) for the development.
I'm having a problem when I want to share my project...
I'm aware that the nRF CLI tools are not yet ported to AArch64 so they don't work natively on Apple Silicon. Normally rosetta 2 is fine, but nrfjprog is not compatible with...
working with nrf52832, sdk 16.0 s132 v7.01
in the uart example i get to this place in the code :
i get a pin toggle which makes my system do some unwanted things...
Hi,
I have a ARM based Linux host CPU connect to MDBT42Q-U(nRF52832).
But I cannot control it by BlueZ:
```
root@OpenWrt:/# btattach -B /dev/ttyMSM1 -P h4 & root...
Hello,
After some weeks of inactivity and moving my desk to an other address, the nRF connect application is not running and show a white screen for all applications except...
Just checking in, I am recently starting to develop cellular communication and looking to develop on the nRF9160. I have been in nRF52 space and with that I develop inside...
Hi, I'm using nrf52840 DK. In my project I want to receive audio from microphone (analog) and stream it to bluetooth headphones. Is there any possible way to do it? Any help...
Hi,
I have been working with a nRF52840 DK up until now, but I need to change and move to a nRF52833 DK. I wanted to adapt my code as they can both use the softdevice I...
Hi all
I'm working on a project based on the nRF52 chip and I'm encountering
If the system runs out of battery or no buttons are pressed within a timeout the system has...
Hello
I made an application on the nRF52 sdk, which works correctly.
Now I want to add the ability to update the firmware via OTA bluetooth.
I followed the instructions...
1. Using Zephyr, trying to config SPI_3 of nrf9160 more than 1MHz for flash interface.
2. Ending up in faults.
3. We need to configure SPI_3 as master with freq > 2MHz...
hello!
im using sdk 17.0.2 with softdevice s112 in our customized board as i want to work for long range mode,so i need extended advertisement ie no available in s112 so...
Hi team.
we are developing project using nrf52 mesh sdk including 1 port nRF52840 and other nrf52 devices. we are finishing dfu mesh for devices.
The nRF52840 gateway...
Hi,
I'm developing a multi-scene application by reference to the "Light switch" example in nRF SDK for Mesh 5.0. The first screenshot show my Elements & Models structrue...
I would like to use the USB dongle with the Openthread CLI example (and eventually an open thread app) as the SDK is just too big and overpowered for my prototypes, I would...
