Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am trying to read data from a chip over SPI.
The implementation of the SPI comms is not ideal as they require a new CS/SS line toggle on every byte. I cannot do a bulk...
I hope that someone can show a clear example of this. I surprised that it isn't in the SDK examples. Basically, it is necessary to stop the BLE SD, in most low-power examples...
Hi,
I am having a problem where the client is unable to receive notification from a peripheral after the softdevice in the peripheral returns 0x3002 after a disconnect....
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of openThread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure...
I am Rattana. I have some project for Bluetooth communicate with mobile phone. Then I will use BC805M(nRF52805).Nomally I connect my MCU with HC06 and I use MCU because I...
Hello I'm now trying to implement the IOS Phones (Central) - Device (Peripheral) liver UART using Multiple Connection - Nordic Uart Service. Devices tried to send a UART signal...
Hi,
We are following the project CHIP and planning on design a matter device with our existing hardware platform. The below are some questions about it:
1. Our platform...
Dear Nordic Bluetooth Experts,
My project is quite simple: A BT Mesh device (generic level server model) powered by a Nordic nRF53832 and an Android app that is used to...
Hi Everyone,
This new way of doing firmware seems to have taken such a turn from what I've been doing for the past 20 years that I don't know where to begin. All I'm trying...
Hello,
I am using android nrf mesh app as a base app and using the latest nrf mesh library version.
I am taking provisioning trails on inline on-off controller.
While...
Hi,
I have used "write_handler(p_ble_evt->evt.gap_evt.conn_handle, p_rtc_service, p_evt_write->data[0]);" to send data to nrf52832 from nrfconnect mobile app but iam able...
Hello,
For our application, we need to form a Zigbee distributed network and not a Zigbee centralized network. That means that routers need to be able to form a new network...
Hi , I have a problem when I wanted to combine the two examples twi scanner and usbd ble uart together although they work correctly individually I have a MAX30105 sensor which...
Hi all
We're developing an application for nrf9160 with zephyr-sdk v2.4.99-ncs2 and nrf-sdk v1.5.1.
In our project we are required to use a Library which forces us to...
Hello
I want to sampling two analog.. with different configuration and handler.
so I set two channels like this.
and then I call only one sample function like...
