Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
Hi,
We are having trouble getting the Thingy91 firmware running as is. We have achieved this in the past but I had made too many modifications and I decided to scrap it...
HI! I'm on Windows x86 and I've followed the steps from the getting started assistant. After trying to locate the board directory ncs/zephyr/boards/arm/nrf9160_pca10090 ,...
I am doing a custom desk for a client and I had this idea of adding a electromagnetic lock on a drawer. That is easy enough but I thought that maybe I could add a couple of...
Hello If I an exemple like ble_thread_dyn_mtd_coap_cli and that I configure the mode in MULTIPROTOCOL_802154_MODE_FAST_SWITCHING_TIMES: do you have any idea how long it takes...
I have two SPI buses on my board, with a different type of slave chip on each. Only a few bytes are read from each during boot. When I use SPIM0, 1 or 2 for them there is...
Newbie here simply trying to run some example projects from the SDK.
Setup:
Segger Embedded Studio 5.10b
Tried example projects in both SDK v17 and v16
nRF52 DK...
We have a working app for SDK 16 and freeRTOS. We wanted to update to SDK 17.0.2 but after upgrading the app hangs up at the first vTaskDelay(). We use configUSE_TICKLESS_IDLE...
Hello, I am a newbie in this forum and I'm not very familiar with app development in general, however I am in the situation in which I have to develop an app to acquire ANT...
Hello Nordic Team,
I am having issues with the HCI UART firmware for the nRF52840 on the Thingy91. I have been using the HCI UART firmware from nRF Connect SDK 1.0.0 for...
Hi, I am working on a project to send commands from mobile to device and vice versa. I am using nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_template . I have made...
Hello,
I am using : SDK 17.0.2 and S132_7.2.0 with nrf52832 DK
in my BLE application, the FDS has 2 behaviors :
1) When the softdevice is enabled : fds_write returns...
Hello,
I´m searching some information about the NB-IoT protocol stack and the overhead which is send with every message.
I nearly searched the whole net but didn't find...
Hi,
It has been stated that nRF9160 doesn't support RLC UNACK, which we have also observed with nRF9160-DK in signalling mode against radio communication tester. Are there...
Hi,
I have a setup where mobile device(central) connect to nrf51dk (peripheral) and exchange data for a time. I want to detect unplanned disconnection of mobile device in...
Hi all, I try read DEVICEID in non-secure application but always return "BUS FAULT", I tried too enable NRF_FICR register in "spm.c" but the error persist!
I try
NRF_FICR_S...