Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I need to transfer data from my ADC (analog to digital conv) on a custom made, nrf52 PCB to a mobile app via bluetooth. For this I integrated my working SPI data transfer...
/** * Copyright (c) 2014 - 2018, Nordic Semiconductor ASA * * All rights reserved. * * Redistribution and use in source and binary forms, with or without modification, * are...
Hi there:
I'm now developing a product with 51822 using the SDK10.0 . The product communicate with another chip through UART.
My problem is when the UART crash with error...
Hi all,
I have an application where I have a mobile app that communicate with up to 20 BLE devices. The BLE devices are RGB LED lights with push buttons and a sensor. I...
Hi.
I'm trying to use nRF52 as TWI slave.
I am using Segger Embedded studio for the coding part and nRF52840 PDK.
I wanted to use TWI between the nRF52840 board and...
Hello Helper,
I am currently running ble_app_uart on 2-3 nRF52 dongles that acts as a node and ble_app_uart_c on nRF-52 DK that acts as a central. While establishing different...
hi:
App <lightblue or nrf connect> (ipone6) connect nrf52832 failed .But using Android won't cause this problem.
Here is the log that failed to connect lightblue...
Hello,
I am using my own board with the NRF52832 device.
I currently have a NRF DFU bootloader programmed and soft device. I used it to download my own App using the NRF...
Hello everyone, I am starting with the NRF52840 dongle. I intend to use it for a Uni project because I'm gonna use it later for work (new product). Since we're using STM32...
Hi everyone! I'm a beginner with BLE. I'm trying to test Eddystone beacon. I'm successfully run "ble_app_eddystone" example in NRF52 SDK, and I also successful connect to...
We are doing some rapid prototyping using PCA10040 boards. I have a bench-top setup with a PCA10040, and some sensors. We want to place our sensors on an Arduino shield, enclose...
Hi there,
I just found an example, Experimental: BLE Multiperipheral Application, https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/ble_sdk_app_multiperipheral...
Hello there,
I have a decent amount of experience using arduino IDE and the arduino micro-controllers to generate PWM signals, but wanted to create an BLE app using the...
Hi
I have sd+dfu uploaded and can download app through dfu with no issues. But if I make any change to the app and try to upload app using Keil uVision then nrf52832 not...
