Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello,
I have the following setup where I am trying to access a function in nrfx_spim.c (red box) from the file mm101_drive.c (green box).
However this function is...
Hi, We have a device configured as a peripheral and want to provide the user with the peer device name typically connected to it, like the device name. Typically a phone will...
I am implementing SPI communication between the intanRHD2132 (ADC) and nRF52840.
I need to periodically send commands(READ, WRITE, etc.) to the IntanRHD2132(ADC) at regular...
We have a sudden problem with the flash_manager. The code stops at static uint32_t flash_area_build(flash_manager_t * p_manager), at line NRF_MESH_ASSERT(p_manager->config...
Hi.
I am designing a 4 layer PCB (0.8mm thick) for an nRF52820 microcontroller.
My board's stack: L1 - Signal L2 - GND L3 - Power L4 - Signal
I have questions regarding...
Hi dear forumers,
I'm in the goal of achieving lowest current consumption on my PCA10056 DK board, with an nrf52840.
I converted a previous zephyr firmware who perfectly...
Hello, I am using the nRF5340 Audio DK with Zephyr and want to use I2S to send audio to an I2S device. So far I have had little success with the microcontroller halting in...
11 months ago in an answer a nordic member wrote (in regards to an error that I now also had and could solve using CONFIG_DEBUG=y):
[quote userid="81283" url="~/f/nordic...
Hi there,
I have an issue when using PPKII software on MacOS at 100ksps (no issue at 1K):
The 10min button at the top does not appear anymore
After a 3min measurement...
Good Afternoon,
I'm designing a 4-layer PCB based on an NRF52832 (QFAA) paired wit h a Molex 479480001 SMT Antenna, and I was hoping for some feedback on Antenna Matching...
Hello,
I'm trying to sniff packets with wireshark by varying the connection interval and supervision timeout of my ble application. I see that with lower connection intervals...
I'm presenting an issue when exporting the data collected, specifically the digital outputs, they are exporting incorrectly, but in the Data Logger tab they are presented...
When implementing AWS_IOT provisioning by claim process, AWS_IOT responds to the published topic $aws/certificates/create/json with a 3580 byte response. This causes TLS to...
Hey, I'm pretty new to Nordic Development. I am working on nRF5340 Audio DK development board right now and I was trying to create a bluetooth speaker kinda setup using the...
