Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
According nrfxlib - modem library - supported features , the nRF9160 firmware supports:
DTLS 1.2 client
TLS 1.2 client
My experience with the TLS client...
Hello,
we have an existing product in "peripheral" role, based on the NRF52832 and soft device S132.
We plan to add support for multi link operation, so that the peripheral...
HI
An example of zigbee multi-sensor is to use log enable info zigbee.report to enable log display. Is there any more information that can be turned on and displayed in...
Hey there! I'm very new to BLE, so I wanted to reach out in this forum to confirm hardware capabilities before I purchase any devices. I'm currently looking at the nRF52840...
hi team,
i am using nrf52840 controller,in my project along with with nrf_sdk.
i wrote a led blicking code using ble protocal on segger IDE 5.40 and i want to see data...
Hi, I'm using nRF52840 in my project. I successfully integrated the BLE DFU service and its characteristics in my firmware, Now I can update the firmware through the nrf-connect...
Hi, we are doing mass production using PLT. And we have found that like 10% of the sensors are stuck in certain stage as seen in following power cycle images.
The program...
Hi,
In the product specification document of nRF52840 it says that in order to read the counter register's value I need to set the capture task NRF_TIMER1->TASKS_CAPTURE...
Hello,
I would like to use the UICR customer registers to store our devices serial numbers.
Can you please point me to some example code for nRF52833 SoC.
I am using...
Hallo Team,
I would like to operate nrf5340 BLE module (BC40C from Fanstel) in "Normal Voltage Mode". Please find the screenshot of the module below. I hope its clear...
Hi,
Just wondering if it's possible, or there is a reliable way to dynamically change the sampling period of the CAF sensor manager module . Specifically the values defined...
Hi everyone!
I am using ESB with the nRF5340dk without ACK, but from time to time need to send a packet with an ACK request in order to send some commands from the receiver...
Hi,
After successful building of pca10040_s132_ble_debug example with changes to project :
- excluding SEGGER_RTT_Syscalls_SES.c from build
- from flash_placement.xml...
Hi,
We are hoping to send our samples for CE certification. We use nrf52805 IC in our design. We do not use any precertified modules.
Looking at the Direct Test Mode folder...
