I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hi,
My development environment:
- VS Code
- nRF Connect SDK: v2.7.0
Description:
- My firmware had successfully paired (with passcode) with an iPhone. Security level...
Hi everyone. When configuring the GATT role, there are GATT server role, GATT client role and both. When using nRF5 SDK or nRF Connect SDK Bare Metal, is it possible to configure...
Hi there!
I'm working through the nrf_cloud_multi_service sample, and have a few questions.
Here is my setup:
nRF9151DK
nRF Connect SDK v2.9.0 and corresponding...
Hello everyone. I've been struggling with directed advertising for a few days now...
I found an example for the peripheral ( github.com/.../direct_adv).
Everything works...
Hi,
I have run the example in ncs 3.1.0 for CS_RAS_Initiator and compared to the older version ncs 3.0.1, there is a new flag called realtime_rd . Thanks to this, I can...
Hi,
I have a question about Channel Sounding: I want to run the CS procedure with 4antenna paths. Both the reflector and the initiator have 2 antennas. I started with the...
Hello!
I know IDAP-Link is not a product from Nordic, so maybe this is not the place to ask this, but...
I have to develop firmware for a custom board based nRF52 that...
I was able to compile and run the Hardware ID example on the nRF5340DK & SDK v3.1.1 using VS Code successfilly, but as soon as I add the overlay-ble-ma c config it still compiles...
This is the first time I've used two roles on one device and I've encountered some oddities.
The topology is as follows: Device A (nRF52840-DK) operates in dual mode (but...
Hi,
I was at the webinar today where they talked about SDK 3.0.0. They mentioned that the QSPI examples were "JESD216 flash" and "JEDEC SPI-NOR flash". I don't see either...
To preface:
Board: nRF9151 custom board nRF Connect SDK / Toolchain: 3.1.0
Hello,
We just received our first article boards for a design that uses a nRF9151 module....
Hello,
After completing DFU on the nRF5340 DK, the default behavior is to reset the MCU. However, instead of performing a full reset, we would like to jump directly to the...
Hi team , I have developed the code where i am able to do OTA in dual slot when my application size is less , but my current application size is aprx. 260 KB and i want top...
When we were using nrfjprog to flash, we used "west flash --erase" because it was quicker to erase entire flash then sector by sector. However, when we upgraded to SDK 3.0...
