Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi, I'm developing an application using fds. I merged fds into ble_app_uart and built complete But when program run fds_init() nRF was crashed I called fds_registered before...
I am using NCS 1.7.0 and latest nRF5340 DK
I am trying to update netcore firmware using the process defined here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1...
Hi everyone!
I have a question regarding the audio support on the nRF52833 chip. Is there any support for sending audio ( Low quality compressed audio ) to headset? Or...
Hi everybody.
For a personal project, I need to integrate a flash or a microSD card to store data.
As computation core I want to use nRF52811, but I'm not able to find...
Hi,
I've lost hours to this so grateful for your support!
I have a custom board using Raytac MDBT42Q, which has a 32MHz clock in the module and I'm not using an external...
To whom it ma concern,
we observed Unkwon Resets after Long runtime ; Several Hours.
We use the NRF52840.
After the reset bit 1 in RESETREAS is detected .
BUT investigation...
My project is based on 'ble_app_uart' and I added dfu service..
so there's two custom 128bit uuid in my project..
But before this, I only want to test dfu service mode...
Hi,
We have made an app that gathers GPS coordinates using an external antenna with the thingy91. The problem we have is that we struggle to test the code when we don't...
Hello,
I am using the nRF52840 dongle with the nrf sniffer 4.1 firmware running on it, using Wireshark to read out its results.
This works fine for advertisement packets...
Hi!
In my application, I am receiving A-GPS data from nRF Cloud. After the data is received there is a considerable amount of time where the GNSS module is blocked because...
Hi,
I am looking into the example of SAADC and sending data through BLE. My tests are based on this example: github.com/.../ble_app_uart__saadc_timer_driven__scan_mode...
Hello,
I have been working on a project that uses nrf52832 custom board. Recently, I have been trying to implement device bonding and realized that the data transfer rate...
Hello All,
Hoping this one is an easy one - have an image for the nRF9160-DK - it hangs unless I make a serial port connection - so, apparently - printk() is blocking waiting...
I like to use nRF52840 now instead of nRF82833 which was used during the CE-RED compliance test. I only like to change the nRF chip. All other components at the PCB will stay...
