Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hi,I am now working with nrf5340 audio sample on nrf5340 audio DK .Here I can able to stream spho645 mic data to other dk board and able to listen using headphone .Now as...
hi Nordic.. i am trying to follow this link https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/exploring-the-benefits-of-mcuboots-compressed-image-support .. in...
Hello,
I’m trying to clarify the maximum ADC input voltage specification for the nRF54L15. Am I correct in assuming that it’s limited to the maximum IO voltage, i.e. VDD...
Hello,
I have developed a BLE Peripheral application on the nRF52840 (SDK 17.1.0) which works correctly. Later, I tried to integrate/port an SPI peripheral example into...
Hi,
I am a bit stuck with configuring nrf5340 project to include the bootloader properly.
The SDK-toolchain I use is v3.0.2
What I need:
encrypted and signed update...
Hello,
We are trying to increase the upload speed of our BMD-350 module. Right now we are averaging about 3kB/s according to nRFConnect.
See attached image of upload...
Hi No rdic support tea m, I'm developing a custo m appl ication on t he Thingy53 and have encountered challen ges implementing two key features that a ren't cov ered in the...
Hi all,
I'm trying to set up MCUMGR on 54L15, such that it can receive images from my border router when they're in the same Thread network. I read that we can upload images...
HI
A phenomenon occurs where the current remains at 20mA intermittently.
Actually, the BLE specification states that RF TX/RX is less than 10mA....
I'd like to know...
We are in the process of porting from nRF SDK v15.3.0 to v17.1.0.
After updating, we’ve noticed that the device sometimes gets stuck. Investigation shows this is related...
I have a custom board using a nrf5340 and a st7789 display using spi and mipi_dbi. It's I have it working on a sample project and printing "Hello World" I was using nrfConnect...
Does this mean that Bluetooth LE Power Control (LEPC) feature is not at all supported by any of the Nordic chipsets? I am particularly curious about nRF54 series with the...
Hello,
Following this link I integrated the extended power save mode in my code,
I put the nrf7002 in extended power save mode after successfully connecting to the AP...
I'll preface this by saying I am new to developing on the nRF and the Zephyr OS.
I am just trying to set up a flash read/write module on my nRF52DK PCA100040 model. From...
I'm using pc-ble driver-master for programming. The hardware uses 52840 dongle and calls SD_API_V5. After I successfully connected, I sent a pairing request using the sd_ble_gap_authenticate...
