I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hello,
Does anyone have some recommendations about what crystal to use with nRF52840?
We have been using FA-20H 32.0000MF10Z-AJ0 but now it is not in stock and we need...
Hello,
I have configured MQTT over TLS to connect to our broker. Everything works great except that the modem stops reconnecting to the broker after exactly 22 connect-disconnect...
Hi, I'm trying to run the nfc_pairing example from the master branch (1.3.99) of NCS. I've successfully built the example in SES and loaded it onto my nRF52840DK, but the...
I'm wondering how BLE signals are handled at the layer below the scanning module. Namely, suppose there are hundreds of BLE modules that are all advertising nearby. How does...
Hi
We are developing a 70 x 70mm PCB containing a nRF52840 for BLE/ESB and a second module for WiFi/BT.
We have no mechanism to avoid transmission of the WiFi module while...
Hi. Sorry, can't find the answer on the forum on my problem.
I am using:
nRF52840 DK
Segger
MacOS
Fanstel BC840 module
I have a project that flashes to Raytac...
Are there any examples of how to enable and use coded phy long range with the nRF Connect SDK? I have the nrf52840DK and would like to create an advertising example to test...
Hello,
In my current project designed around nRF52840 incorporating many peripherals (limited power budget) and many central devices. Each peripheral can connect to any...
Hi
I am using NRF52810 with Softdevice S112 7.0.1 and SDK 16
I want to ask about the behavior of the softdevice notification queue on disconnect. I have seen these two...
Hi .thank u for reading this .First sorry for my english. This is the story:
I try to make a flexible mesh using multi nrf24l01+ more than 10 nodes. I searched so many topic...
While running a Scan in nRFConnect 4.24.3 on Android 10, Nokia 6.2, I see the first Advertisement from my BLE Device. That device advertises different sets of ScanData over...
Hi ,
I am working on a project where i need to publish wifi scans over ble , issue is that when ever we try to send data over it either send or not sent to avoid data loss...
Does Nordic have some solution for this? Device would be a WiFi+BLE gateway, which runs Linux, and can support advertising scan for at least 300 beacons, and have Ethernet...
Hi, I am running into issues where the nRF9160 (in NB-IoT mode) does not seem to handle cell changes reliably. I am using modem firmware mfw_nrf9160_1.2.0 . I made a simplified...
