FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
Hi,
I'm testing the ble_app_uart example on the nRF52840 DK and it seems to be consuming a lot of current similar to the case in https://devzone.nordicsemi.com/f/nordic...
In a single core BLE SOC, whenever a BLE event occurs the BLE stack takes high priority and any application code running on the single core, is delayed while the event is...
Hi ,
I need to store strings in flash and came across the NVS. I referred to the example in samples/subsys/nvs and was able to do the nvs operation.
The following are...
Hey, so I was under the belief that the maximum size of data one can include in a BLE packet is 20 bytes (23 bytes total, 3 bytes overhead, so 20 total for custom data). With...
Hello! I have been working on bluetooth for some time and I just worked with connectable advertising until now. This time I am trying to add a beacon functionality too. The...
Hello,
I am developing a BLE and IEEE 802.1.4 multiprotocol device. I implemented a parser to change some settings of the device. T he configuration is updated with this...
Hi,
I'm trying to implement a SPI Communication between Arduino UNO and PCA10056 DK. PCA10056 DK run as a SPI slave.. Arduino uno run as a SPI Master.
The problem is...
I'm using SDK 15.3.0 and SoftDevice 6.1.1 running on an nRF52832.
The iOS application works correctly when it is running in the foreground. It is able to connect and bond...
Hi,
I am trying to develop an application for Thingy:91, which would allow me getting data from BLE and sending it to the cloud with LTE. I am working on NCS 1.3.0.
Of...
I just tested with the example project, "ble_app_uart" using SDK, "nRF5SDK17009d13099.zip" on nRF52DK (labelled with PCA10040 1.2.4 2018.23) board on Segger embedded studio...
Hi ,
i am trying to interface a WINBOND W25Q64JV flash module with NRF52,i can able to read device id,status register success fully.
i wrote the data in particular address...
Hi,
I'm using nRF52840 DK as a central. Our project is based on ble_app_uart_c example. There is filter for UUID only during scan.
I noticed, that for conection establishing...
I'm using the nrfjprog command "nrfjprog -f nrf52 --reset". This sometimes causes my custom board to hang. I dont think it is able to boot at all, I do not see any uart output...
