This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Hi everyone,
I’m currently working on setting up Azure communication using the latest SLM version for PPP (Point-to-Point Protocol) support. Here’s the configuration I’m...
We have a Waveshare display and a npm1300dk and I wanted to know the proper way to add the npm1300's config.overlay file, generated by nrfConnect's PowerUp, to the west command...
Hi,
I faced some issues regarding multiple IRQ_CONNECT being onvoked on the same irq and I went into this post :
LPUART nRF5340 fatal error - Nordic Q&A - Nordic DevZone...
Hello! I am using nRF Connect SDK 2.6.0v. I created a west workspace and i want to make custom board. I took reference from Devacademy nRF Connect SDK Intermediate Lesson3...
Hello Nordic
Use NRF52832 、 NCS 1.6 、“zephyr\samples\basic\blinky” sample.
In hardware, my board doesn't have a low-speed clock, and the reset pin is floating. Therefore...
Can the nrf7002 be set up to have both a STA virtual interface and an AP virtual interface at the same time?
From all the documentation it doesn't specify that only one...
Hello List,
I have an Arduino Nano 33 ble with nrf52840. It is powered directly with 3.3 Volt using 7 Volt and a 3.3 Volt LDO voltage regulator. It is programmed (via the...
I am using nRF52820 and the SDK is nRF5_SDK_17.1.0_ddde560. When setting advertising data, I am trying to enter the chip's BD address for individual identification. Is there...
Hi support Team,
I would like to know the SDK version to be used for nRF54L15.
Is there any link to know details regarding the configuration, flashing and example codes...
So, I follow the zephyr docs ( https://docs.zephyrproject.org/latest/kernel/services/synchronization/events.html )
and define an event as:
However I get the error: ...
Hello Engineer Greeting of the day i am building my product using nrf52833 IC , there are some communication modules connected to the 52833 , i want to cheack lowest power...
Hi currently i am using nrf52840 sdk ver 17.1.0 s140 i am using the sdk flash storage example in .\.\_nRF5_SDK_17.1.0_ddde560\examples\peripheral\flash_fstorage where i am...
Hello, when building the MQTT sample in the nRF Connect SDK, `getaddrinfo()` is returning only -2 when built for the nRF9161 dev kit. I'm using the onomondo SIM that came...
Dear DevZone Nordic Team,
I am currently working on a project involving the nRF9160DK , and I need guidance on how to operate and output GPS values in the debug console...
I am learning how to use MCUMGR. I generally understand it, but I have some concerns.
- The firmware with the private key can also be overwritten. Then it will not boot...