Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Our system is composed of a nrf5340, a QSPI flash, and a nrf7002 on single wire SPI. We are not using the network processor.
We are using Zephyr NCS 2.9 with sysbuild. We...
I am testing the Sleep idle current for the nRF52833QDAA module.
The module is nothing connected outside except the fundamental circuit as the attached picture shown.
...
Hello,
We have the nRF52833 included in a new PCB design. So far it works well using mcuboot and a UART interface.
I'm trying to get the radio set up and running, and...
NCS: v2.7.0 nRFCloud/utils: a2db3ffedbda237f9c1efb7a68ec2d270c346e56 Hardware: Custom Board with nRF9161 I am writing a provisioning automation (with robotframework), but...
Hi,
I am using sensor observer sample to get the data from sensor sample. However, I notice the power consuption is too high. I have look thourgh the forum and found this...
HI
this is my pm_static.pmy
I added the following in app.overlay
After the compilation passed, there was no response when I flashed the device.
this is my...
Hii,
I'm using Distributer and target sample code for testing OTA in ble mesh. Using nrf Device Manager App I'm able to upload dfu_application.zip file to distributer...
I have installed the nRF BTLE Sniffer plugin for Wireshark to do some transmission monitoring between my PC (central) and device (peripheral). To test, I have a U-Blox NINA...
Dear Support Team,
I am currently working with two nRF54L15 DK boards placed approximately 50 cm apart and stationary. I am using the channel_sounding_ras_ example with...
Hey! I am working with 2 nrf5340 boards(nrf5340 Audio-DK as peripheral and nrf534DK as Central) and am trying to send 12750 bytes of data at one second from Audio-DK to DK...
Hello,
I am new to BLE Mesh and working with Zephyr. However, I've found the supported BLE Mesh samples to be very helpful in understanding the protocol and the environment...
hello Nordic
we have a master version that runs with older ncs version of mcuboot, and it is running ncs2.5.0 based app.
we have a release version that runs with ncs2...
Hi I want to download nRF_DeviceFamilyPack.8.15.0 for my Keil project but I cannot download with pack Installer and manually. If I want to donwload this package from website...
According to the data sheet, the nrf54l05/10/15 has 4 power domains. And there is a low-power domain. I search through the entire datasheet for a few hours and still couldn...
