Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
I am using S132 4.0.2 and SDK 13, and I have theese questions:
I have an application where BLE node establishes multiple concurrent connections (several as central...
Hello,
I'm having systematically an HardFault interrupt ~10 seconds after calling sd_soft_device_enable(NULL, &fault_handler);
This occurs on my bootloader code, but...
Hallo Community,
I am doing the example ble_app_uart using Eclipse, a SDK 13.00 and a board 10040, When i compile the main file I´ve problems with scan params:
#if ...
#define UART_TX_BUF_SIZE 1024
#define UART_RX_BUF_SIZE 1024
Why to send and receive buffer length of the definition of 1024 bytes, increase the value, again if serial port...
Hi, I just bought the PCA10031 nRF51422 based USB dongle and PCA10028 nRF51422 based development board.
The difference between nRF51822 and nRF51422 was the ANT protocol...
Can I use below code to send data packets continuously over nus (>20 packets)
i=UserUart.RxBuf[1]+2;
index = 0;
while(i>0)
{
if(i>20)
{
while((err_code = ble_nus_string_send...
Hi,
I am using nRF52 chip with SDK13.0. MTU size 155.
I am connect with device using android phone. After sending 1 byte command device starting to send continuous notification...
hello there i think i need two uart in my application. i read datasheet of both nrf51 and nrf52
in both there is only one uart.
can anyone have implemented software uart...
Use this routine E:\nordic\nRF5_SDK_12.2.0_f012efa3\examples\proprietary_rf\gzll\experimental\gzp_desktop_emulator
To modify the can communicate with PC nrf24luep pairing...
Hi.
I'm troubled.
I use nRF52 preview DK v0.9.0 & Keil5.
i tried ble_app_hrs_c in example folder of nRF52_SDK.
This program stopped at
err_code = sd_softdevice_enable...
Hello all,
I am actually implementing an SPI-master driver in non blocking mode, I write the following code, when I use a debeug led, the program enters well in the IRQ...
I started with the blu_app_template on a 52840. I have advertising working. I can see that from an iOS app. I can also see the details of the service. I see the characteristic...
I am using the Master Emulator C# examples to build my own application. None of the examples are able to properly connect to a remote device. When I open up the Master Control...
I'm writing an nRF52 DK btle application using SDK 12. The DK comunicates with 2 external peripheral via SPI and I2C interfaces. Complilation fails with the error:
._build...
hi, i am reading mpu6050 with nrf51822. every now and then the data got corrupt because of softDevice interrupts. if i don't use Softdevice the it runs perfectly but when...
