Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi,
I'm having an issue including USB DFU Trigger library in my prototype application running on nRF52833.
My application is based on the ble_uart example, to which I...
Hi,
My application is written on top of freertos ble example. I need to integrate radio test example as well for certification. I am running into errors when I try to...
Hello,
my first Post here, so i hope i do it correctly.
I have the following Problem with the Configuration and Communication over TWI/I2C.
The Voltage of the TWI...
I am working on BLE on NRF52840 using soft devices for BLE and I was using sd_ble_gap_ppcp_set API to set the connections parameters for the BLE so I think the PPCP is the...
I'm calling this function from a Zepyhr project:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/connectivity/bluetooth/api/gap.html#group__bt__gap_1gad2e3caef88d52d720e8e4d21df767b02...
Hi, I am trying to test multi_sensor example from Zigbee and Thread SDK 4.2 using official Nordic nrf52840DK with few Zigbee hubs. Example is located in \examples\zigbee\experimental...
Hi
My thingy91 does not appear in the Connected Devices list in VS Code. I've tried everything now.
What's the prerequisites for getting this to work?
Do I have to install...
I'm using a nRF5340DK with nRF Connect SDK v1.9.0 and want to use MCUBoot with Direct-XIP.
Using the hello_world sample project, I added MCUBoot.
In the MCUBoot prf.conf...
I have issues with my NRF5340DK devices that I'm hoping to get support on. Several devices appear to be bricked, stuck in a boot loop or otherwise unable to program using...
Hi, I'm hoping someone could advise on interfacing with the T2 LC3 codec included in nRF Connect.
The context is I have stereo I2S microphones providing 24-bit 2's complement...
Hello, As part of a student project I am looking to learn about Nordic technologies for BLE and ANT. The goal of our end of study project is to provide an extremely accurate...
If I would like to add Bluetooth capability to the nrf9160, can the nrf5340 be used as a "companion" MCU?
Would be great if there is a pre-build firmware for the nrf5340...
Hi,
I am trying to write a program that connects my phone to my nRF52840-DK board; I then send one of two commands from my phone, then the nRF52 will respond accordingly...
