Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi,
Our product is based on nRF5340 and will run DFU over BLE.
Now I am testing the DFU function via the "Firmware Upgrade" in device manager APP.
In the current architecture...
hi, could you tell why I build SDK17.1.0 (nRF5_SDK_17.1.0_ddde560\examples\peripheral\csense_drv\pca10040\blank\arm5_no_packs) demo code, it appears that mistake (.\_build...
I am trying to send data in peripheral but my central connected to other peripheral .
So I decided to add whitelist in central.
In which function to add whitelist
...
Hi!
I would like to add into my Zephyr project a library called Vanetza , which depends on Boost++, Cryptopp and GeographicLib. I am still learning CMake and I don't know...
Hi
sdk : ncs v2.1.0
example : serial_lte_modem
I used the following command to test and found that sending the character "failed, how should I set it so that I can...
Hello,
I'm working on an application that uses the aws_iot_send function ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/networking/aws_iot.html...
How to make nRF Connect SDK submit to other code management servers (such as bitbucket,Not github), And continue to use Git to manage this code?
I will modify the content...
Hi all,
I recently installed the nRF Connect SDK and have had some success. Very snazzy.
I have seen some issues with the JLink on the DK resetting during firmware validation...
I cannot seem to get floating point supoort for printf/scranf
It works for LOG_INF
I have tried the following .conf settings:
CONFIG_NEWLIB_LIBC =y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Hi All!
I am trying to program the external nrf9160 SOC using nrf9160 DK using the following connections. Before that, I tried the same connections to program the nrf52820...
When I set CONFIG_LOG=y, CONFIG_SERIAL=y in prj.conf, the UART streams out diagnostic message from my application code as expected, but I also get this endless I2C error message...
I am using NRF52832 for my project.
Refer the following Softdevice and SDK versions.
Softdevice: S132_2.0.0-7.alpha
SDK Version: 4.0.0-2.alpha
Question 1:...
I am using nRF Connect SDK 1.9.0 and the NRF52840.
When building samples/keys/hw_unique_key you get this warning:
----------------------------------------------------...
Hi,
My nRF52840 dongle which was working fine in the past doesn't seem to be responding properly. Is there anything I can do?
Some background:
1 - I have used it...
