Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hello,
I have the Adafruit nRF52832 Bluefruit LE module, I need to program it through VS Code. I don't have any other J-Link Connector. Is it possible to program the module...
I'm developing a system using BLE Mesh with the intent of having a "collector" node attached to each network that manages provisioning and received published data from connected...
Hello,
It seems that there are no boardfiles or dts files for nRF52840-QFAA in NCS 2.0.0., there is only support for the QIAA version.
Customer built a board with the...
When I use 52832 to develop a mesh project and want to use uart to print information, I find that the code always reports an error because of the existence of printf. The...
Hello, while I was examining the BMD-380 datasheet, a section of which I shared the picture below caught my attention. What does factory image mean? I want to implement Bluetooth...
We are developing a product using the N52810 chip. We have J-link, and by downloading and connecting the Rf test tool,
the result is that there is no firmware. Can you support...
My device and Software details are as below
nRF52840 EVK
Softdevice:s140
SDK v16
We are looking to use freeRTOS instead of zephyr on this board.
Finally with freeRTOS...
Dear Nordic support team
I tried to change the sample of ble_app_uart (nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040e) to support connecting 4 mobile...
I am working on an e-paper display with Bluefruit nRF52832 . I need to transfer a large image bitmap over Bluetooth Low Energy (BLE).
As BLE can send 255 bits at once, how...
Hi there,
We are using nrf9160 DK v1.0.0 ( pca10090 ). SES version 5.68 nrf Connect SDK 1.9.1 Windows 10
I want to make it as spi slave on pins CS=p0.10, mosi=p0.11, miso...
Hello Team,
We are developing an application with nRF52832 and ncsv1.8.0.
We are using NUS service to share data between Mobile and Nordic Chip. With the help of nRF...
Hey there!
The DFU over serial was successfully implemented. Unfortunately, I was only able to update the first node of my mesh, not all of them.
The first node in the...
Hello!
Recently I want to write a hci vs command in zephyr using nrf connect sdk, when I track ncs_v1.9.1\zephyr\samples\bluetooth\hci_pwr_ctrl samples code and find it...
