Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Dear Nordic Engineer
Our costomer has developed a keyboard using LLPM in NCS.Now Now they have encountered some problems.We have been working with them for a long time but...
Hi. I am returning to developing on Nordic devices after some time away, enticed back by nrfConnect / VSCode support for MacOS. I am running MacOs Monterey 12.1 and I have...
The dumped stack information (especially the PC) point to what was running when the WD fired. This makes sense to me, but conflicts with the advice posted in the question...
Hello Nordic, Our procurement team is worried that the nRF52832 has reached end of life. I wanted to confirm if this is the case? If this is not the case, when is it expected...
Hi, community.
From the official document, I have learned how network core Bootloader works.
It can write data from shared SRAM to the corresponding flash address of Nework...
Hello,
i'm programing a nrf52832 and a nrf52805 and I'm using the peripheral uart example, I would like to change the size of the bytes of my rx and tx that I can send...
Hi
I have a board nRF52840 configured with some QSPI with filesystem configured
I would like to manage the file system from an app and I saw that - nRF Connect Device...
I'm working on a project where we need to store into FLASH about 1350 bytes of compressed data at about 2HZ (twice a second). This is my first Nordic/Zephyr project, so I...
Hi
I'm working with an nrf52840-dk on NCS 1.8.0.
I'm attempting to interface the board with an LS7366R quadrature counter over SPI; however, I'm not receiving any count...
hello Nordic
i am using ppk2 pca63100,
working on linux (manjaro), installed the nrfConnect v3.9.3 with power profiler v3.3.0
1. when i connect a device i have to...
This question relates to the unsatisfying reponse to ticket 283390.
The technology of the processor is not important. Arm Cortex processors are as fine as several others...
I am having trouble setting up a GPIO pin that will toggle when the radio is active on the network core. I have tried adding the code in bluetooth.c from the ppi_trace sample...
Hi everyone!
I am developing a board using a nrf52 as a BLE interface for an arduino. My idea in the future is update the firmware of the Nrf52 with OTA. But i wanna do...
Hello everyone. I am trying to set up a BLE central-peripheral network using nrf52840 based on NUS service. I need up to more than 10 peripherals which is customized board...
Hello there,
I'm trying to make a transceiver simulation on nRF24L01+ using Simulink. The block diagram provided in the documentation/datasheet was not clear enough for...
